Husqvarna 1151436-95 User Manual
40 – English
TECHNICAL DATA
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 357XP and 359. The
combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and
vibration requirements of ANSI B 175.1–2000.
combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and
vibration requirements of ANSI B 175.1–2000.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a hard nose.
corresponding maximum nose radius of a hard nose.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
will also achieve kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose
radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose
radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
Bar and chain combinations
Chain saw models Husqvarna 357XP and 359 met the kickback performance requirements of ANSI B 175.1-2000 when
tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a
low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We
recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 357XP and 359.
Other chain saw models may not meet the kickback requirements when equipped with the listed bar and chain
combinations.
tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a
low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We
recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 357XP and 359.
Other chain saw models may not meet the kickback requirements when equipped with the listed bar and chain
combinations.
Note: For the saw chains above (if available) you are free to choose between 0,050" or 0,058" gauge drive links for the
corresponding bar, see the table below.
corresponding bar, see the table below.
Bar
Chain
Length, inch
Pitch, inch
Gauge, inch
Max. nose radius
Type
Drive link count
13
0,325
1,5
10T
Husqvarna H25
56
15
0,325
1,5
10T
64
16
0,325
1,5
10T
66
18
0,325
1,5
10T
72
20
0,325
1,5
12T
78
13
0,325
1,3
10T
Husqvarna H30
56
15
0,325
1,3
10T
64
16
0,325
1,3
10T
66
18
0,325
1,3
10T
72
20
0,325
1,3
10T
78
15
3/8"
1,5
11T
Husqvarna H42
56
16
3/8"
1,5
11T
60
18
3/8"
1,5
11T
68
20
3/8"
1,5
11T
72
24
3/8"
1,5
11T
84
0,050”
H30
H22
0,058”
-
H25