Shindaiwa C2510/EVC User Manual
OFF
Ignition
switch
NEVER operate the unit with the cut-
ting attachment shield or other protec-
tive devices removed!
ting attachment shield or other protec-
tive devices removed!
Use only authorized Shindaiwa parts and
accessories with your Shindaiwa trimmer.
Do not make modifications to this unit with-
out written approval from Shindaiwa, Inc.
accessories with your Shindaiwa trimmer.
Do not make modifications to this unit with-
out written approval from Shindaiwa, Inc.
ALWAYS make sure the cutting attach-
ment is properly installed and firmly
tightened before operation.
ment is properly installed and firmly
tightened before operation.
NEVER use a cracked or warped
cutting attachment: replace it with a
ser viceable one.
cutting attachment: replace it with a
ser viceable one.
Checking Unit Condition
ALWAYS make sure the cutting attach-
ment fits properly into the appropriate
attachment holder. If a properly installed
attachment vibrates, replace the attach-
ment with new one and re-check.
ment fits properly into the appropriate
attachment holder. If a properly installed
attachment vibrates, replace the attach-
ment with new one and re-check.
ALWAYS stop the engine immediately
and check for damage if you strike a
foreign object or if the unit becomes
tangled. Do not operate with broken or
damaged equipment.
and check for damage if you strike a
foreign object or if the unit becomes
tangled. Do not operate with broken or
damaged equipment.
NEVER allow the engine to run at high
RPM without a load. Doing so could dam-
age the engine.
RPM without a load. Doing so could dam-
age the engine.
NEVER operate a unit with worn or dam-
aged fasteners or attachment holders.
aged fasteners or attachment holders.
WARNING!
A cutting attachment shield or
other protective device is no guarantee
of protection against ricochet. YOU
MUST ALWAYS GUARD AGAINST
FLYING DEBRIS!
of protection against ricochet. YOU
MUST ALWAYS GUARD AGAINST
FLYING DEBRIS!
12
Idle the engine briefly before stopping
(about 2 minutes), then slide the ignition
switch to the “O” (Engine OFF) position.
(about 2 minutes), then slide the ignition
switch to the “O” (Engine OFF) position.
Stopping the Engine
Adjusting Engine Idle
Idle Adjusting
Screw
The engine must return to idle speed
whenever the throttle lever is released.
Idle speed is adjustable, and must be set
low enough to permit the engine clutch to
disengage the cutting attachment.
whenever the throttle lever is released.
Idle speed is adjustable, and must be set
low enough to permit the engine clutch to
disengage the cutting attachment.
WARNING!
The cutting attachment must
NEVER rotate at engine idle! If the
idle speed cannot be adjusted by
the procedure described here, return
the unit to your Shindaiwa dealer for
inspection.
idle speed cannot be adjusted by
the procedure described here, return
the unit to your Shindaiwa dealer for
inspection.
Idle Speed Adjustment
Place the unit on the ground, then start
1.
the engine, and then allow it to idle 2-3
minutes until warm.
minutes until warm.
If the attachment rotates when the
2.
engine is at idle, reduce the idle speed
by turning the idle adjustment screw
counter-clockwise.
by turning the idle adjustment screw
counter-clockwise.
If a tachometer is available, adjust idle.
3.
Check Specifications page for correct
idle speed
idle speed
Starting the Engine (continued)
NOTE
Carburetor fuel mixture adjustments are
preset at factory and cannot be serviced
LQWKH¿HOG
preset at factory and cannot be serviced
LQWKH¿HOG
Disconnect the spark plug lead and use
1.
the spark plug wrench to remove the
spark plug (turn counter clockwise to
remove).
spark plug (turn counter clockwise to
remove).
Slide the ignition switch to the “O”
2.
(STOP) position.
If the spark plug is fouled or
Ŷ
soaked with fuel, clean the plug as
necessary.
necessary.
Open the choke and fully depress the
3.
throttle lever with your left hand, then
pull the starter handle rapidly with your
right hand to clear excess fuel from the
combustion chamber.
pull the starter handle rapidly with your
right hand to clear excess fuel from the
combustion chamber.
Replace the spark plug and tighten it
4.
firmly with the spark plug wrench. If a
torque wrench is available, torque the
spark plug to the values recommended
in the “Specifications” section.
torque wrench is available, torque the
spark plug to the values recommended
in the “Specifications” section.
Repeat the starting procedure for a
5.
warm engine.
If the engine still fails to start, refer to
6.
the troubleshooting section near the
end of this manual.
end of this manual.
Starting A Flooded Engine