Vestax PMC-CX User Manual
10
Change to "IF-500"
q Remove the fader knob. (See fig-a)
w Remove the 4 screws which fix the input fader panel to the mixer. (See fig-b)
e Remove the 2 screws which fix the input fader. (See fig-c)
w Remove the 4 screws which fix the input fader panel to the mixer. (See fig-b)
e Remove the 2 screws which fix the input fader. (See fig-c)
r Remove the input fader, and carefully remove the multi-cable connecter from the fader unit. (See fig-d)
t Replace the fader unit making sure to that the connector wires are securely fastened before carefully positioning the fader unit
t Replace the fader unit making sure to that the connector wires are securely fastened before carefully positioning the fader unit
and affixing with screws.
INPUT FADER
HOW TO CHANGE THE FADER UNIT
fig-a
fig-b
fig-c
fig-d
7
!5 MASTER LEVEL VOLUME
Adjusts the signal level outputs from MASTER OUT1/2
JACKS $7 on the rear panel.
JACKS $7 on the rear panel.
!6 MASTER CUE SWITCH
Used to send the signal from MASTER OUT1/2 to the
monitor section for headphone monitoring. When switch
is on, an indicator lights up.
monitor section for headphone monitoring. When switch
is on, an indicator lights up.
!7 CF CURVE VOLUME
djusts the crossfader curve. A clockwise rotation gives a
sleep crossfade which is good for scratching and cutting.
whereas a counter clockwise rotation gives a gentle
crossfade, good for long running mixes.
sleep crossfade which is good for scratching and cutting.
whereas a counter clockwise rotation gives a gentle
crossfade, good for long running mixes.
!8 MASTER LEVEL METER
The VU analog level meters indicate the L and R outputs.
!9 PGM LEVEL METER
The LED bar level meters indicate the PGM channel.
@0 BOOTH MONITOR EQ VOLUME
Adjusts the HI/MID/LOW frequencies for the BOOTH
OUT.
OUT.
@1 BOOTH MONITOR LEVEL VOLUME
Adjusts the output level of BOOTH MONITOR.
@2 BOOTH MONITOR MUTE SWITCH
This switch mute the signal being sent to the BOOTH
OUT.
OUT.
@3 ANTI PHASE ON / OFF SWITCH
This switch is used to activate an antiphase effect on the
Master Isolator Section. Essentially, an antiphase flips the
isolator curve upside down on both the low and mid frequency
ranges, which thereby creates a reverb type effect on the signal
being outputted.
Master Isolator Section. Essentially, an antiphase flips the
isolator curve upside down on both the low and mid frequency
ranges, which thereby creates a reverb type effect on the signal
being outputted.
@4 MASTER ISOLATOR HI
This rotary dial section can be used to isolate the Hi
frequencies on any MASTER SECTION input signal.
frequencies on any MASTER SECTION input signal.
@5 MASTER ISOLATOR MID
This rotary dial section can be used to isolate Mid frequencies
on any MASTER SECTION input signal.
on any MASTER SECTION input signal.
@6 MASTER ISOLATOR LOW
This rotary dial section can be used to boost the Low
frequencies on any MASTER SECTION input signal.
frequencies on any MASTER SECTION input signal.
@7 ISOLATOR ON / OFF SWITCH
This switch is used to turn the Master Isolator Volume Section
either on or off. When set to the "OFF" position the full range
of input signal being sent to the MASTER section will be
heard regardless of the position of the Master Isolator Volume
rotary dials.
either on or off. When set to the "OFF" position the full range
of input signal being sent to the MASTER section will be
heard regardless of the position of the Master Isolator Volume
rotary dials.
@8 CROSS FADER
Mixes the signals assigned by the CROSSFADER ASSIGN
SWITCHES to either side of the crossfader. When the
crossfader is set in the center position, both the left and right
signals will be heard. This fader is user replaceable and may be
changed easily by following this user guide's instructions
carefully. See "HOW TO CHANGE THE FADER UNIT".
*Replace this fader with a Vestax CF-50 replacement
SWITCHES to either side of the crossfader. When the
crossfader is set in the center position, both the left and right
signals will be heard. This fader is user replaceable and may be
changed easily by following this user guide's instructions
carefully. See "HOW TO CHANGE THE FADER UNIT".
*Replace this fader with a Vestax CF-50 replacement
inputfader.
MASTER SECTION
18
19
17
21
22
27
23
26
28
25
24
20
15
16
PMC-CX/E 04.4.26 10:16 AM ページ 11