Dynacord 2200-3 User Manual
P
OWER
M
ATE
3
24
CAUTION:
On most recorders the input signal is
directly carried through to the outputs.
In case you have connected both, the
REC SENDS and the 2TRACK IN, and
the PowerMate’s 2TRACK to MASTER
control is set to anything but its lowest
setting, the recorded signal is included
in the master mix again. The difference
in delay of the two signals is responsi-
ble for dropouts and general degrada-
tion of the sound. In the worst case,
activating the RECORD button on your
tape deck could lead to very unpleasant
feedback noise. To prevent this from
happening make sure to set the
2TRACK to MASTER control to their
lowest settings.
directly carried through to the outputs.
In case you have connected both, the
REC SENDS and the 2TRACK IN, and
the PowerMate’s 2TRACK to MASTER
control is set to anything but its lowest
setting, the recorded signal is included
in the master mix again. The difference
in delay of the two signals is responsi-
ble for dropouts and general degrada-
tion of the sound. In the worst case,
activating the RECORD button on your
tape deck could lead to very unpleasant
feedback noise. To prevent this from
happening make sure to set the
2TRACK to MASTER control to their
lowest settings.
63 - 2TRACK IN L/R
Here you can connect a recorder, a CD/MP3 player, an
open reel or an additional SUB-mixer. The signal is
post master fader and post STANDBY switch, which
allows playing intermission music during performance
breaks or checking the mix during the rehearsal, using
the headphones. You just have to engage the STAND-
BY switch to mute all channel signals at the master
outputs. The 2TRACK IN signal however will pass un-
obstructed.
open reel or an additional SUB-mixer. The signal is
post master fader and post STANDBY switch, which
allows playing intermission music during performance
breaks or checking the mix during the rehearsal, using
the headphones. You just have to engage the STAND-
BY switch to mute all channel signals at the master
outputs. The 2TRACK IN signal however will pass un-
obstructed.
HINT: The 2TRACK IN signal is not available at the
REC SEND connectors, the DIGITAL AUDIO
INTERFACE or the MASTER B OUTPUTS in
PRE fader mode.
INTERFACE or the MASTER B OUTPUTS in
PRE fader mode.
64 - 2TRACK
TO
MASTER
This control is used to mix the 2TRACK signal to the
master mix, post fader of the master controls.
master mix, post fader of the master controls.
CAUTION:
When adjusting the level of the device
that is connected to the 2TRACK IN –
CD player, tape deck, etc. – always
begin with the 2TRACK to MASTER con-
trol set at its minimum setting. Other-
wise, depending on the output quality
of the connected sound source, the out-
putted level can instantly “hit the top”.
that is connected to the 2TRACK IN –
CD player, tape deck, etc. – always
begin with the 2TRACK to MASTER con-
trol set at its minimum setting. Other-
wise, depending on the output quality
of the connected sound source, the out-
putted level can instantly “hit the top”.
65 - REC SEND & USB OUT
This control allows adjusting the volume at the REC
SEND outputs or, when used, the level of the DIGITAL
AUDIO INTERFACE output channels.
SEND outputs or, when used, the level of the DIGITAL
AUDIO INTERFACE output channels.
66 - LAMP 12V/5W
This XLR-type socket provides a DC voltage of 12V/
5 watts and is meant for the connection of a goose-
neck lamp. Please make sure that the used lamp com-
plies with the here mentioned specifications and pin
assignment. We recommend using the gooseneck
lamp (DC-LITLITE-4P), available from the DYNACORD
accessory assortment. For further information, please
consult your local dealer.
5 watts and is meant for the connection of a goose-
neck lamp. Please make sure that the used lamp com-
plies with the here mentioned specifications and pin
assignment. We recommend using the gooseneck
lamp (DC-LITLITE-4P), available from the DYNACORD
accessory assortment. For further information, please
consult your local dealer.