Energizer CH15MNCP4 Leaflet

Your 15 minute AA/AAA Battery Charger is 

designed to charge Energizer Nickel Metal Hydride 

(NiMH) rechargeable batteries. The included AA 

2200mAh batteries are ready for use in 15 minutes. 

It has four channels; you can charge one to four AA 

or AAA batteries simultaneously.
SAVE THESE INSTRUCTIONS
This manual contains important safety and 

operating instructions for your charger. Before 

using your charger, read all instructions and 

cautionary markings on the battery charger, the 

batteries to be charged, and the product that uses 

the batteries. 

1. To reduce the risk of injury, charge only 

rechargeable NiMH batteries with the charger. 

Other types of batteries might burst, causing 

personal injury or damage to your charger. 

2. For indoor use only. Do not expose charger to 

rain, snow or excessive moisture. 

3. Never use an extension cord or any attachment 

not recommended by Energizer. May result in a 

risk of fire or electric shock.

4. Do not use plug adapters without approved, 

country specific voltage transformers.

5. Do not operate the charger if it has been 

subjected to shock or damage. 

6. Do not disassemble the charger. Incorrect 

reassembly may result in a risk of electric shock 

or fire. 

7. Always unplug the charger from outlet before 

attempting maintenance or cleaning.

8. Never alter the plug provided. Improper 

connection can result in a risk of electric shock. 

This Charger is not intended for use by young 

children or infirm persons without supervision. 

Young children should be supervised to ensure 

they do not play with the charger. 
WARNING:  Read charger instructions carefully. 

Charge only rechargeable nickel metal hydride 

batteries. Charging any other type of rechargeable 

or non-rechargeable (disposable) batteries may 

cause them to leak, rupture or explode, causing 

injury.  CAUTION:  Risk of electric shock. Dry 

location use only. Batteries may become hot to the 

touch while charging.
BATTERY WARNING:

 Charge with only standard 

household Nickel Metal Hydride battery chargers. 

Do not open battery, dispose of in fire, put in 

backwards, mix with other battery types or short 

circuit – may ignite, explode, leak or get hot, 

causing injury. 

1. Plug the AC adapter’s barrel plug into the DC 

input jack of the charger.

2. Plug the AC adapter into a standard AC outlet.

1. Plug the DC car adapter output plug into the DC 

input jack of the charger.

2. Plug the large end of the cord into the 12V car 

accessory/lighter port.

3. Place 1-4 batteries into battery compartment 

according to the polarity symbols (+ and -) 

marked inside each bay.  Indicator light will 

change to red to indicate charging

4. If the indicator light flashes red try the following 

suggestions.

• Confirm battery polarity (+/- contacts) are 

correctly oriented in charger bay.

• Check the battery position in the bay, to insure 

battery contacts are touching charger contacts.

• Remove the batteries and gently wipe the 

battery and charger contacts with a clean dry 

cloth.

• The charger may be detecting a defective 

battery, which will prevent charging.

5. The LED indicator turns GREEN, the batteries 

are ready for use. You can remove the battery for 

use.  To obtain maximum performance, batteries 

may be left in charger an additional 10 minutes 

after the LED turns off. 

6. Unplug the adapter from the outlet when 

charging is completed.

• To get the best performance, charge the batteries 

in an area between 59 and 77 degree F. If the 

area is too warm, the batteries will not be fully 

charged. If the area is too cold, the batteries can 

permanently lose their ability to charge.

• It is normal for batteries to become warm while 

charging and is no cause for alarm.