Epson 810 Series User Manual
*411685500*
*411685500*
If anything is missing, contact Epson as described on the back.
Caution:
Do not open ink cartridge packages until you are ready to install the ink.
Cartridges are vacuum packed to maintain reliability.
Canada only: For French speakers, remove the sticker from the backing sheet and
place it on the right side of the control panel.
place it on the right side of the control panel.
Remove all protective materials from the printer, including from inside the
paper cassette.
paper cassette.
1
Raise the scanner and remove the transportation lock.
2
Store the transportation lock as shown.
3
Lower the scanner.
Unpack
1
Start Here
Make settings
3
1
Select your language and country.
Touch the screen to select the desired option. Press or to see more
countries.
countries.
2
For the Daylight Saving Time setting, select
Summer if your region uses
Daylight Saving Time and it’s currently in effect. (DST is effective from
spring through summer.) Otherwise, select
spring through summer.) Otherwise, select
Winter to turn off the setting.
Press
OK.
3
Select the date format.
4
Use the numeric keypad to set the date, then press
OK.
5
Select the time format.
6
Use the numeric keypad to set the time.
7
Press
OK when done.
Note:
You can change the date and time settings by pressing the Home button,
selecting
Setup, selecting Printer Setup, then Date/Time. For more information on
using and adjusting the control panel, see your Quick Guide.
2
Squeeze the edge guides and slide them out. Then insert paper with the
glossy or printable side face-down.
glossy or printable side face-down.
3
Slide the edge guides against the paper.
4
Lower the photo tray.
5
Squeeze the edge guides and slide them out. Then insert 4 x 6-inch or
5 x 7-inch photo paper with the glossy or printable side face-down.
5 x 7-inch photo paper with the glossy or printable side face-down.
Note:
Make sure the paper fits under the edge guides.
6
Slide the edge guides against the paper.
7
Keep the cassette flat as you insert it.
8
Extend the output tray and flip up the stopper.
5
Load paper
Install ink cartridges
4
Note:
Do not load paper yet.
1
Lift up the scanner.
2
Unpack the ink cartridges.
3
Remove only the yellow tape from each cartridge.
Caution:
Don’t remove any other seals or the cartridges may leak.
4
Insert the cartridges in the holder for each color. Press each cartridge
down until it clicks.
down until it clicks.
5
Lower the scanner.
6
Wait while ink charges. Charging takes about 5 minutes.
Note:
Your Artisan 810 Series ships with full cartridges and part of the
ink from the first cartridges is used for priming the Artisan 810 Series.
Replacement cartridges will print more pages.
Replacement cartridges will print more pages.
Caution:
Don’t turn off the Artisan 810 Series while the ink system is
initializing or you’ll waste ink.
(Included for
Canada only)
1
Connect the power cable.
Caution:
Do not connect to your
computer yet.
Turn on and adjust
2
2
Press the
On button, then raise the
control panel.
To lower the control panel, press the
Unlock button.
Unlock button.
Caution:
To avoid damaging your Artisan 810
Series, always press the
Unlock button to lower
the control panel.
The paper cassette has 2 trays. The main tray is for letter-size, legal-size,
or 8 x 10-inch paper. The photo tray is for 4 x 6- or 5 x 7-inch photo paper.
or 8 x 10-inch paper. The photo tray is for 4 x 6- or 5 x 7-inch photo paper.
1
Pull out the paper cassette. Then slide back the photo tray and lift it up.
Phone cord
Power cord
Series