Nxp Semiconductors UM10237 User Manual
UM10237_2
© NXP B.V. 2008. All rights reserved.
User manual
Rev. 02 — 19 December 2008
271 of 792
NXP Semiconductors
UM10237
Chapter 11: LPC24XX Ethernet
The magic packet detection unit analyzes the Ethernet packets, extracts the packet
address and checks the payload for the Magic Packet pattern. The address from the
packet is used for matching the pattern (not the address in the SA0/1/2 registers.) A magic
packet only sets the wake-up interrupt status bit if the packet passes the receive filter as
illustrated in
address and checks the payload for the Magic Packet pattern. The address from the
packet is used for matching the pattern (not the address in the SA0/1/2 registers.) A magic
packet only sets the wake-up interrupt status bit if the packet passes the receive filter as
illustrated in
: the result of the receive filter is ANDed with the magic packet
filter result to produce the result.
Magic Packet filtering is enabled by setting the MagicPacketEnWoL bit of the RxFilterCtrl
register. Note that when doing Magic Packet WoL, the RxFilterEnWoL bit in the
RxFilterCtrl register should be 0. Setting the RxFilterEnWoL bit to 1 would accept all
packets for a matching address, not just the Magic Packets i.e. WoL using Magic Packets
is more strict.
register. Note that when doing Magic Packet WoL, the RxFilterEnWoL bit in the
RxFilterCtrl register should be 0. Setting the RxFilterEnWoL bit to 1 would accept all
packets for a matching address, not just the Magic Packets i.e. WoL using Magic Packets
is more strict.
When a magic packet is detected, apart from the WakeupInt bit in the IntStatus register,
the MagicPacketWoL bit is set in the RxFilterWoLStatus register. Software can reset the
bit writing a 1 to the corresponding bit of the RxFilterWoLClear register.
the MagicPacketWoL bit is set in the RxFilterWoLStatus register. Software can reset the
bit writing a 1 to the corresponding bit of the RxFilterWoLClear register.
Example: An example of a Magic Packet with station address 0x11 0x22 0x33 0x44 0x55
0x66 is the following (MISC indicates miscellaneous additional data bytes in the packet):
0x66 is the following (MISC indicates miscellaneous additional data bytes in the packet):
<DESTINATION> <SOURCE> <MISC>
FF FF FF FF FF FF
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
11 22 33 44 55 66 11 22 33 44 55 66
<MISC> <CRC>
9.16 Enabling and disabling receive and transmit
Enabling and disabling reception
After reset, the receive function of the Ethernet block is disabled. The receive function can
be enabled by the device driver setting the RxEnable bit in the Command register and the
“RECEIVE ENABLE’ bit in the MAC1 configuration register (in that order).
be enabled by the device driver setting the RxEnable bit in the Command register and the
“RECEIVE ENABLE’ bit in the MAC1 configuration register (in that order).
The status of the receive datapath can be monitored by the device driver by reading the
RxStatus bit of the Status register.
RxStatus bit of the Status register.
illustrates the state machine for the
generation of the RxStatus bit.