Lucent Technologies P/N 80051 Leaflet
DS2000 PC Card Instructions for Backup,
Restore and Software Upgrade
Restore and Software Upgrade
(U Slot Software)
Use PC Card P/N 85880 to back up and restore your site data. Use PC Card P/N 80051-V**.** to load or update
your system’s software. (Note that **.** denotes the level of the system software loaded on PC Card P/N 80051.)
your system’s software. (Note that **.** denotes the level of the system software loaded on PC Card P/N 80051.)
PC Card P/N 80051 is a system software PC Card only.
You cannot use it to back up and restore site data.
Backing Up Site Data
To use PC Card P/N 85880 to back up site data:
1. Insert PC Card P/N 85880 into the CPU (see the figure
at right).
2. Be sure the CPU mode switch is set to
RUN
.
3. Enter the programming mode.
ICM + #*#* + 372000 + HOLD
4. Dial 9906 + HOLD.
You see: START?
To quit program 9906 instead of going to the next step,
dial N + HOLD.
To quit program 9906 instead of going to the next step,
dial N + HOLD.
5. Dial Y + HOLD.
You see: 9906: DATABASE NAME
6. Enter a name for the database you want to save (up to
10 characters long).
Refer to Keys for Entering Names at right if you need help
when entering names.
Skip this step if you want to save data in an address
that already has a name assigned.
when entering names.
Skip this step if you want to save data in an address
that already has a name assigned.
7. When you are done entering the name, press HOLD.
You see the name and date of the first database stored.
If no databases are stored, you see: 9906: DB00
(empty)
If no databases are stored, you see: 9906: DB00
(empty)
8. The system assigns the name you entered in step 7 to
the address you select below:
Press VOL
▲
or VOL
▼
to scroll through the 16 data
base addresses (DB 00 through DB 15).
OR
Skip this step to select the currently displayed data
base.
base.
9. Press HOLD.
Normally, you see 9906: SAVING . . . . . . . . .
The PC Card Active LED is on during backup.
If the address you choose already has data stored in it,
you see: REPLACE DB nn Y/N.
- Press N + HOLD to back up to step 5.
- Press Y + HOLD to proceed.
You automatically exit programming when the backup
completes.
The PC Card Active LED is on during backup.
If the address you choose already has data stored in it,
you see: REPLACE DB nn Y/N.
- Press N + HOLD to back up to step 5.
- Press Y + HOLD to proceed.
You automatically exit programming when the backup
completes.
80
00
0
00
0
- 27A
NEC America,
Inc.
INSER
T
M
EGAB
YTE
L
INEAR
F
LASH
www.cng.nec.com
Keys for Entering Names
Press this
key:
Then one of these keys to enter the character in the white cell:
1
2
3
4
#
1
&
-
(dash)
1
/
(backslash)
1
‘
(apostrophe)
1
1
2
A
B
C
2
3
D
E
F
3
4
G
H
I
4
5
J
K
L
5
6
M
N
O
6
7
P
Q
R
S
7
8
T
U
V
8
9
W
X
Y
Z
9
0
SPACE
:
0
*
*
#
To enter characters in lower case (e.g.,
e
instead of
E
), press
MW
before pressing the key in the
first shaded column. Use
LND
to backspace over (erase) any characters you want to correct.
1
In software versions prior to 02.00.00, the codes for 1 + 2, 1 + 3, and 1 + 4 were not available.
Continued
Mode Switch
PC Card Active
LED
LED