Adder Technology AVX4016IP User Manual

. To.begin.the.upgrade.process,.click.the.Upload Now.button..The.progress.

will.be.shown.within.the.dialog..Should.you.decide.not.to.continue.with.
the.upload.at.any.stage,.click.the.Abort.button;.response.to.this.is.usually.
immediate,.however,.during.an.erase.command,.the.upload.will.not.be.
aborted.until.the.erase.is.complete.(this.may.take.a.few.seconds).

. Click.switch.1.on.the.rear.of.the.AdderView.CATx.to.the.OFF.position.and.

disconnect.the.power..When.the.power.is.re-applied.the.AdderView.CATx.
will.operate.using.the.new.firmware.

Issues to consider when performing flash upgrades
The.upgrade.program.rewrites.the.AdderView.CATx.firmware.code..If.the.
upgrade.process.is.interrupted.then.the.AdderView.CATx.will.have.invalid.code.
and.will.not.be.able.to.operate..It.is.therefore.good.practice.to.ensure.that.the.
upgrade.process.is.always.fully.completed..A.partial.or.failed.upgrade.may.be.
rectified.by.performing.another.upgrade..If.the.upgrade.process.is.interrupted.
accidentally.then.you.should.immediately.repeat.the.upgrade.process.without.
moving.switch.1.from.the.upgrade.(ON).position..Switch.1.forces.the.AdderView.
CATx.into.flash.upgrade.mode.and.prevents.the.upgraded.code.from.being.run..
Running.faulty.or.partially.upgraded.code.may.have.unpredictable.results.and.
may.damage.your.AdderView.CATx.or.computing.equipment..
WARNING: Running faulty or partially upgraded code may have unpredictable 
results and may damage your AdderView CATx or computing equipment.

. The.results.of.the.unit.query.will.be.displayed.in.the.Device/Dongle.Selection.

dialog:..

. The.type.and.firmware.revision.of.each.discovered.CAM.will.be.displayed.

alongside.the.port.number.to.which.it.is.connected.

. Using.the.Device/Dongle.Selection.dialog.you.can.determine.which.items.

should.receive.a.firmware.upgrade:

•. Use.the.Program / Verify Main Unit.option.to.include.or.exclude.the.

AdderView.CATx.unit.itself.

•. Use.the.

Select All CAMs.option.to.upgrade.every.discovered.CAM.

•. Use.the.Select All USB / PS2 / Sun CAMs.options.to.upgrade.only.CAMs.

of.a.certain.type.

•. Use.the.individual.port.options.to.select.particular.CAM.devices.to.

upgrade.

. When.the.required.options.have.been.selected,.click.OK.
. Note: Approximate upgrade times are: AdderView CATx unit = 4½ minutes; 

. From.the.main.KVM.Firmware.Uploader.dialog,.click.the.Browse....button.

and.select.the.upgrade.file.that.is.appropriate.to.your.AdderView.CATx.unit:

. AdderView.CATx.16.port:..

AD_CAT16.TXT

. AdderView.CATx.IP.16.port:..

AD_IP16.TXT

. AdderView.CATx.24.port:..

AD_CAT24.TXT.

. AdderView.CATx.IP.24.port:..

AD_IP24.TXT

. .The.upgrade.file.details.will.be.displayed.within.the.dialog.
. IMPORTANT: Check that the ‘Intended Target Units’ field matches the