Acoustic Energy LT35 User Manual

(

→ "Power/Status/Lamp Indicator" on page 

Does not turn on

Will turn off

No picture

Picture suddenly
becomes dark

Color tone or hue is
unusual

Image isn’t square to
the screen

Picture is blurred

Image is scrolling
vertically, horizontally
or both

Remote control does
not work

Indicator is lit or
blinking

Cross color in RGB
mode

• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote

control is on. (

→ page 

• Ensure that the lamp cover is installed correctly. (

→ page 

• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the

room where you are presenting is particularly warm, move the projector to a cooler location.

• Check to see if the lamp usage exceeds 2100 hours (up to 2600 hours : Eco mode). If so, replace the lamp.

After replacing the lamp, reset the lamp hours used.(

→ page 

• The lamp may fail to light. Wait a full minute and then turn on the power again.

• Ensure that the Power Management or Off Timer is off. (

→ page 

• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,

Video or S-Video). (

→ page 

• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. (

→ page 

• Check to see if the image is muted. (

→ page 

• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. (

→ page 

• Enter your registered keyword if the Security function is enabled. (

→ page 

• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on

the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-

saver or power management software.

• See also the next page.

• When one of the following happens, the Lamp mode automatically changes from Normal to Eco.

* When there are no signals (blue or black screen) 

→ To return to the Normal mode, select another available

source.

* When the room where you' re presenting is particularly warm 

→ Move the projector to a cooler location.

• Check if an appropriate color is selected in [Wall Color]. If not, select an appropriate option. (

→ page 

• Adjust [Hue] in [Picture]. (

→ page 

• Reposition the projector to improve its angle to the screen. (

→ page 

• Use the Keystone correction function to correct the trapezoid distortion. (

→ page 

• Make sure that focus is appropriate.
• Reposition the projector to improve its angle to the screen. (

→ page 

• Ensure that the distance between the projector and screen is within the adjustment range of the lens. (

→ page

• Make sure that the distance between the focus sensor and the screen is within the effective range of the Auto

Focus. (

→ page 

• Make sure that the requirements for the Auto Focus are met. (

→ page 

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-

Video or Computer). (

→ page 

• Adjust the computer image manually with the Horizontal and Vertical in the [Image Options] 

→ [Position/

Clock]. (

→ page 

• Install new batteries. (

→ page 

• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. (

→ page 

• See the POWER/STATUS/LAMP Indicator. (

→ page 

• Press the AUTO ADJ. button on the projector cabinet or the remote control. (

→ page 

• Adjust the computer image manually with [Clock] and [Phase] in [Image Options] 

→ [Position/Clock] in the

menu. (

→ page 

For more information contact your dealer.