Sunfire TGP-5 User Manual
User's Manual
25
GUIDE
MENU
MODE
MODE
EXIT
INFO
SYSTEM
+10
POWER
3
1
6
4
9
7
ENT
DIS
M3
M1
2
5
8
0
M2
PAGE
FAV
MAIN
OFF
VOL
CH
MUTE
PREV
CH
CD
AUDIO
MAIN
TAPE
AUX
ZONE2
TGP5
DVD
VCR
SAT
TV
CABLE
RC-500
CHAPTER 3
Remote Control
Think of the TGP-5 remote control
as ten remotes in one. There are ten
DE VICE buttons, fi ve on either side
of the display, and each allows the
remote to operate one piece of equip-
ment.
DE VICE buttons, fi ve on either side
of the display, and each allows the
remote to operate one piece of equip-
ment.
From the factory, the device buttons
are labeled: CD, TAPE, AUX, ZONE2,
TGP-5, DVD, VCR, SAT, TV and
CA BLE.
TGP-5, DVD, VCR, SAT, TV and
CA BLE.
Only the TGP-5 and ZONE2 but-
tons are pre-programmed, and these
allow the remote to operate your TGP-
5. The remote can be set to operate
your other remote controlled equip-
ment. This is done in three ways from
the hidden SETUP menu:
allow the remote to operate your TGP-
5. The remote can be set to operate
your other remote controlled equip-
ment. This is done in three ways from
the hidden SETUP menu:
1. Entering a code from the tables at
the end of this manual
2. Stepping through the codes
3. Learning from your other remotes
See Remote Setup on page 27 for
more details.
LCD Display
The top line shows the present
device, mode or status, and it shows
when a remote command is being
transmitted. The bottom line shows
the page number, status and basic
in struc tions during programming.
when a remote command is being
transmitted. The bottom line shows
the page number, status and basic
in struc tions during programming.
The main part of the display shows
the labels of the ten DE VICE buttons.
You can change any label and cus-
tomize the remote to fi t your sys tem.
Note: this is not a touch-sensitive
screen, just a way of labeling the
device buttons on each side, and
showing in struc tions and status.
You can change any label and cus-
tomize the remote to fi t your sys tem.
Note: this is not a touch-sensitive
screen, just a way of labeling the
device buttons on each side, and
showing in struc tions and status.
Contrast
The contrast of the display can be
changed by holding down the MAIN
button and pressing the joystick pad
UP or DOWN.
button and pressing the joystick pad
UP or DOWN.
Light
The button on the right side of the
remote briefl y turns on the lights for
the buttons and display. Pressing it
again will turn it off. The number of
sec onds can be varied, or it can be
disabled.
the buttons and display. Pressing it
again will turn it off. The number of
sec onds can be varied, or it can be
disabled.
Device Buttons.
Once you press a device button,
all the device buttons change label
and function to become buttons to
operate your device. There are two
pages per device, and you can move
be tween them using the PAGE button.
and function to become buttons to
operate your device. There are two
pages per device, and you can move
be tween them using the PAGE button.
PAGE
Use this to jump to various display
pages. For example, if you press the
TGP-5 device button, the display
chang es to some show buttons which
control your TGP-5. If you press
PAGE, the display will move to page
2, showing more func tions for the
TGP-5.
TGP-5 device button, the display
chang es to some show buttons which
control your TGP-5. If you press
PAGE, the display will move to page
2, showing more func tions for the
TGP-5.
MAIN
This button will return the remote
display back to the Main menu.
Depending on which mode you are
in, it may take two or more presses.
This will help you get back to the
Main menu if you ever get lost in the
menus.
Depending on which mode you are
in, it may take two or more presses.
This will help you get back to the
Main menu if you ever get lost in the
menus.
FAV
This button allows you to step
through fi ve display pages of your
favorite TV and radio stations. These
can be set and re-labeled to suit.
favorite TV and radio stations. These
can be set and re-labeled to suit.
Joystick Pad
This pad and surrounding buttons
are used to operate standard DVD
menus, and VCR and Tape transport
controls. In TGP-5 mode, if you press
MENU, the On Screen Display will ap-
pear and the joystick can be used to
select and adjust the various items.
menus, and VCR and Tape transport
controls. In TGP-5 mode, if you press
MENU, the On Screen Display will ap-
pear and the joystick can be used to
select and adjust the various items.
LIGHT
MAIN
JOYSTICK
MACROS
M1, M2 and M3 Macros
These MACRO buttons can be
programmed to send out a se quence
of commands with a single press.
of commands with a single press.
Batteries
The remote takes four AAA bat-
teries inside the rear compartment.
These should last about six months
in normal use, before a low-battery
warning appears.
These should last about six months
in normal use, before a low-battery
warning appears.
LCD
DEVICE
Buttons
DEVICE
Buttons
PAGE
IR WINDOW
FAV