Emulex Single Channel 2Gb/s Fibre Channel PCI HBA LP9002L-E LP9002L-E Leaflet
Product codes
LP9002L-E
2Gb/s Fibre Channel
www.emulex.com
LP9002L
STANDARDS
FC-PH 1, 2, 3:
Fibre Channel physical and signaling interface
standards
Fibre Channel physical and signaling interface
standards
FC-PI:
Fibre Channel physical interface
Fibre Channel physical interface
FC-MJS:
Fibre Channel methodologies for Jitter specification
Fibre Channel methodologies for Jitter specification
FCP:
Fibre Channel protocol for SCSI standard
Fibre Channel protocol for SCSI standard
PCI:
Local bus specification version 2.2
Local bus specification version 2.2
ARCHITECTURE
Emulex Centaur ASIC technology up to 66MHz PCI
bus master DMA
bus master DMA
2Gb/s or 1Gb/s FC Link
2MB FLASH memory
1MB code RAM
256KB buffer RAM
2MB FLASH memory
1MB code RAM
256KB buffer RAM
SOFTWARE ENVIRONMENTS
Windows Server 2003
Windows 2000
Windows NT
HP-UX
Linux
NetWare
Solaris
AIX
Windows 2000
Windows NT
HP-UX
Linux
NetWare
Solaris
AIX
HARDWARE ENVIRONMENTS
x86, SPARC and PowerPC PCI hardware platforms
3.3 or 5v signaling
3.3 or 5v signaling
OPTICAL
Data rates: 1.0625/2.125Gb/s
Optics:
short-wave single-mode lasers
Cable:
9/125µm single-mode fiber
50/125µm multi-mode fiber
62.5/125µm multi-mode fiber
short-wave single-mode lasers
Cable:
9/125µm single-mode fiber
50/125µm multi-mode fiber
62.5/125µm multi-mode fiber
Connector: LC
Distance:
(1Gb/s)
500 meters (1640’) 50/125 µm fiber
300 meters (984’) 62.5/125 µm fiber
(1Gb/s)
500 meters (1640’) 50/125 µm fiber
300 meters (984’) 62.5/125 µm fiber
(2Gb/s)
300 meters (984’) 50/125 µm fiber
150 meters (492’) 62.5/125 µm fiber
300 meters (984’) 50/125 µm fiber
150 meters (492’) 62.5/125 µm fiber
PHYSICAL DIMENSIONS
Short, low profile MD2 form factor
Low profile or standard bracket
167.64mm x 64.41mm (6.60” x 2.54”)
Low profile or standard bracket
167.64mm x 64.41mm (6.60” x 2.54”)
POWER REQUIREMENTS
Volts: +3.3 VDC (± 5%)
Power: 7.2 watts typical (9.3w max)
Power: 7.2 watts typical (9.3w max)
ENVIRONMENTAL CONDITIONS
Operating temperature:
0° to 45°C (32° to 113°F)
0° to 45°C (32° to 113°F)
Airflow required:
100 lf/m
100 lf/m
Storage temperature:
-40° to 70°C (-40° to 158°F)
-40° to 70°C (-40° to 158°F)
Relative humidity:
5% to 95% non-condensing
5% to 95% non-condensing
AGENCY APPROVALS
Class 1 Laser Product per DHHS 21CFR (J)
& EN60825
& EN60825
UL recognized to UL 1950
CUR recognized to CSA22.2, No. 950
TUV certified to EN60950
FCC rules, Part 15, Class A
ICES–003, Class A
EMC Directive 89/336/EEC (CE Mark)
- EN55022, Class A
- EN55024
- EN55022, Class A
- EN55024
Australian EMC Framework (C–Tick Mark)
- AS/NZS 3548, Class A
- AS/NZS 3548, Class A
VCCI, Class A
DRIVER SUPPORT
The LightPulse® LP9002L is complemented by a
rich suite of software support including storage
protocol (SCSI), network protocol (IP) as well as
concurrent multi-protocol (SCSI & IP) operation,
enabling advanced Storage Area Network (SAN)
implementations in Windows Server 2003,
Windows 2000, Windows NT, HP-UX, Linux,
NetWare, Solaris and AIX environments. All drivers
are also fully compatible with the entire line of
Emulex LightPulse Fibre Channel HBAs.
rich suite of software support including storage
protocol (SCSI), network protocol (IP) as well as
concurrent multi-protocol (SCSI & IP) operation,
enabling advanced Storage Area Network (SAN)
implementations in Windows Server 2003,
Windows 2000, Windows NT, HP-UX, Linux,
NetWare, Solaris and AIX environments. All drivers
are also fully compatible with the entire line of
Emulex LightPulse Fibre Channel HBAs.
This document refers to various companies and products by their trade
names. In most, if not all cases, their respective companies claim these
designations as trademarks or registered trademarks. This information
is provided for reference only. Although this information is believed to
be accurate and reliable at the time of publication, Emulex assumes no
responsibility for errors or omissions. Emulex reserves the right to make
changes or corrections without notice.
names. In most, if not all cases, their respective companies claim these
designations as trademarks or registered trademarks. This information
is provided for reference only. Although this information is believed to
be accurate and reliable at the time of publication, Emulex assumes no
responsibility for errors or omissions. Emulex reserves the right to make
changes or corrections without notice.
05-158 11/04
Corporate HQ 3333 Susan Street Costa Mesa CA 92626 714 662.5600 | Wokingham U.K. (44) 118 977 2929 | Paris France (33) 41 91 19 90 | Beijing China (86 10) 6849 9547
SPECIFICATIONS
LightPulse
®
PCI Host Bus Adapter
MANAGEMENT INTERFACE
Emulex HBAs also support the common HBA API
Management Interface (FC-MI Annex A). This
provides the ability to monitor, discover, and control
the fabric from a management application.
The management API allows the HBA to provide a
common and consistent view of a Fibre Channel
SAN which will significantly reduce the total cost of
ownership for customers.
Management Interface (FC-MI Annex A). This
provides the ability to monitor, discover, and control
the fabric from a management application.
The management API allows the HBA to provide a
common and consistent view of a Fibre Channel
SAN which will significantly reduce the total cost of
ownership for customers.
ORDERING INFORMATION
LP9002L–F2
embedded multi–mode optic interface (LC)
embedded multi–mode optic interface (LC)