APC 6739380EN/JC User Manual
6739380EN/JC -
Page 45
Inverter On/Off commands
Display for the inverter On/Off commands
Direct access to the function by pressing
the "I/O" button .
the "I/O" button .
This screen is displayed if the inverter is already
off. It is a prompt to press the "*" button to
confirm start-up. During start-up, the following
screen is displayed:
off. It is a prompt to press the "*" button to
confirm start-up. During start-up, the following
screen is displayed:
This screen is displayed if the inverter is on. It is
a prompt to press the "*" button to confirm
shutdown.
If the transfer to Mains 2 conditions are not
correct, the following screen is displayed a few
seconds:
a prompt to press the "*" button to confirm
shutdown.
If the transfer to Mains 2 conditions are not
correct, the following screen is displayed a few
seconds:
Following confirmation of the command, the
system automatically returns to the initial
screen.
system automatically returns to the initial
screen.
PROCESSING
…
…
COMMAND REFUSED
TRANSFER IMPOSSIBLE
TRANSFER IMPOSSIBLE
Language, display contrast and buzzer volume settings
Direct access to the function by pressing the
"settings" button.
"settings" button.
Selection of the display language: English,
French, German, Italian, Spanish, Dutch,
Swedish, Finnish, Portuguese.
French, German, Italian, Spanish, Dutch,
Swedish, Finnish, Portuguese.
This screen is a prompt to set the display
contrast by successively pressing the ">" button.
When the setting is confirmed by pressing the
"*" button, the system goes on to the buzzer.
contrast by successively pressing the ">" button.
When the setting is confirmed by pressing the
"*" button, the system goes on to the buzzer.
When this screen is displayed, the buzzer
automatically turns on. Press the ">" button
several times to adjust the volume. After
confirmation of the buzzer volume by the "*"
button, the system automatically returns to the
initial screen.
automatically turns on. Press the ">" button
several times to adjust the volume. After
confirmation of the buzzer volume by the "*"
button, the system automatically returns to the
initial screen.
Display of the settings selection screens
◗
if a "Soft Tunor" session is in
progress (initiated by after-sales
support technicians), pressing the "I/O"
button produces the message:
support technicians), pressing the "I/O"
button produces the message:
COMMAND INVALID
SOFT TUNOR
These commands may be accessed
only via the master display. When the
"I/O" button is pressed, the series of
screens in the figure opposite is
displayed.
only via the master display. When the
"I/O" button is pressed, the series of
screens in the figure opposite is
displayed.
Note:
◗
these commands do not concern the
Static Switch Cubicle. The "I/O" button
on the "static switch" cubicle produces
the message:
on the "static switch" cubicle produces
the message:
COMMAND INVALID
STATIC SWITCH MODUL
◗
the "I/O" button on a slave display
monitor produces the message:
COMMAND INVALID
ON SLAVE DISPLAY
◗
if the On/Off commands have not
been validated (by the after-sales
support technicians), pressing the "I/O"
button produces the message:
support technicians), pressing the "I/O"
button produces the message:
COMMAND INVALID
CONFIGURATION
These settings may be accessed by
pressing the "settings" button.
The series of screens in the figure
opposite is displayed.
pressing the "settings" button.
The series of screens in the figure
opposite is displayed.
*
*
START INVERTER ?
=YES >=ESCAPE
=YES >=ESCAPE
or
initial screen
initial screen
*
STOP INVERTER ?
=YES >=ESCAPE
=YES >=ESCAPE
*
LANGUAGE = ENGLISH
=CONFIRM.
=CONFIRM.
initial screen
*
DISPLAY CONTRAST
>=SELECT =CONFIRM.
>=SELECT =CONFIRM.
*
BUZZER VOLUME
>=SELECT =CONFIRM.
>=SELECT =CONFIRM.
*
*
*
*
"Monitor" alphanumeric display
(cont.)