Cisco Systems 3130 User Manual
21-7
Cisco Catalyst Blade Switch 3130 for Dell Software Configuration Guide
OL-13270-01
Chapter 21 Configuring DHCP Features and IP Source Guard
Understanding DHCP Features
Each database entry (binding) has an IP address, an associated MAC address, the lease time (in
hexadecimal format), the interface to which the binding applies, and the VLAN to which the interface
belongs. The database agent stores the bindings in a file at a configured location. At the end of each entry
is a checksum that accounts for all the bytes from the start of the file through all the bytes associated
with the entry. Each entry is 72 bytes, followed by a space and then the checksum value.
hexadecimal format), the interface to which the binding applies, and the VLAN to which the interface
belongs. The database agent stores the bindings in a file at a configured location. At the end of each entry
is a checksum that accounts for all the bytes from the start of the file through all the bytes associated
with the entry. Each entry is 72 bytes, followed by a space and then the checksum value.
To keep the bindings when the switch reloads, you must use the DHCP snooping database agent. If the
agent is disabled, dynamic ARP inspection or IP source guard is enabled, and the DHCP snooping
binding database has dynamic bindings, the switch loses its connectivity. If the agent is disabled and only
DHCP snooping is enabled, the switch does not lose its connectivity, but DHCP snooping might not
prevent DHCP spoofing attacks.
agent is disabled, dynamic ARP inspection or IP source guard is enabled, and the DHCP snooping
binding database has dynamic bindings, the switch loses its connectivity. If the agent is disabled and only
DHCP snooping is enabled, the switch does not lose its connectivity, but DHCP snooping might not
prevent DHCP spoofing attacks.
When reloading, the switch reads the binding file to build the DHCP snooping binding database. The
switch updates the file when the database changes.
switch updates the file when the database changes.
When a switch learns of new bindings or when it loses bindings, the switch immediately updates the
entries in the database. The switch also updates the entries in the binding file. The frequency at which
the file is updated is based on a configurable delay, and the updates are batched. If the file is not updated
in a specified time (set by the write-delay and abort-timeout values), the update stops.
entries in the database. The switch also updates the entries in the binding file. The frequency at which
the file is updated is based on a configurable delay, and the updates are batched. If the file is not updated
in a specified time (set by the write-delay and abort-timeout values), the update stops.
This is the format of the file with bindings:
<initial-checksum>
TYPE DHCP-SNOOPING
VERSION 1
BEGIN
<entry-1> <checksum-1>
<entry-2> <checksum-1-2>
...
...
<entry-n> <checksum-1-2-..-n>
END
Each entry in the file is tagged with a checksum value that the switch uses to verify the entries when it
reads the file. The initial-checksum entry on the first line distinguishes entries associated with the latest
file update from entries associated with a previous file update.
reads the file. The initial-checksum entry on the first line distinguishes entries associated with the latest
file update from entries associated with a previous file update.
This is an example of a binding file:
2bb4c2a1
TYPE DHCP-SNOOPING
VERSION 1
BEGIN
192.1.168.1 3 0003.47d8.c91f 2BB6488E Gi1/0/4 21ae5fbb
192.1.168.3 3 0003.44d6.c52f 2BB648EB Gi1/0/4 1bdb223f
192.1.168.2 3 0003.47d9.c8f1 2BB648AB Gi1/0/4 584a38f0
END
When the switch starts and the calculated checksum value equals the stored checksum value, the switch
reads entries from the binding file and adds the bindings to its DHCP snooping binding database. The
switch ignores an entry when one of these situations occurs:
reads entries from the binding file and adds the bindings to its DHCP snooping binding database. The
switch ignores an entry when one of these situations occurs:
•
The switch reads the entry and the calculated checksum value does not equal the stored checksum
value. The entry and the ones following it are ignored.
value. The entry and the ones following it are ignored.
•
An entry has an expired lease time (the switch might not remove a binding entry when the lease time
expires).
expires).
•
The interface in the entry no longer exists on the system.
•
The interface is a routed interface or a DHCP snooping-trusted interface.