Cisco Systems 3130 User Manual
37-5
Cisco Catalyst Blade Switch 3130 for Dell Software Configuration Guide
OL-13270-01
Chapter 37 Configuring EtherChannels and Link-State Tracking
Understanding EtherChannels
Port Aggregation Protocol
The Port Aggregation Protocol (PAgP) is a Cisco-proprietary protocol that can be run only on Cisco
switches and on those switches licensed by vendors to support PAgP. PAgP facilitates the automatic
creation of EtherChannels by exchanging PAgP packets between Ethernet ports. You can use PAgP only
in single-switch EtherChannel configurations; PAgP cannot be enabled on cross-stack EtherChannels.
For more information, see the
switches and on those switches licensed by vendors to support PAgP. PAgP facilitates the automatic
creation of EtherChannels by exchanging PAgP packets between Ethernet ports. You can use PAgP only
in single-switch EtherChannel configurations; PAgP cannot be enabled on cross-stack EtherChannels.
For more information, see the
By using PAgP, the switch or switch stack learns the identity of partners capable of supporting PAgP and
the capabilities of each port. It then dynamically groups similarly configured ports (on a single switch
in the stack) into a single logical link (channel or aggregate port). Similarly configured ports are grouped
based on hardware, administrative, and port parameter constraints. For example, PAgP groups the ports
with the same speed, duplex mode, native VLAN, VLAN range, and trunking status and type. After
grouping the links into an EtherChannel, PAgP adds the group to the spanning tree as a single switch
port.
the capabilities of each port. It then dynamically groups similarly configured ports (on a single switch
in the stack) into a single logical link (channel or aggregate port). Similarly configured ports are grouped
based on hardware, administrative, and port parameter constraints. For example, PAgP groups the ports
with the same speed, duplex mode, native VLAN, VLAN range, and trunking status and type. After
grouping the links into an EtherChannel, PAgP adds the group to the spanning tree as a single switch
port.
PAgP Modes
shows the user-configurable EtherChannel PAgP modes for the channel-group interface
configuration command.
Switch ports exchange PAgP packets only with partner ports configured in the auto or desirable modes.
Ports configured in the on mode do not exchange PAgP packets.
Ports configured in the on mode do not exchange PAgP packets.
Both the auto and desirable modes enable ports to negotiate with partner ports to form an EtherChannel
based on criteria such as port speed and, for Layer 2 EtherChannels, trunking state and VLAN numbers.
based on criteria such as port speed and, for Layer 2 EtherChannels, trunking state and VLAN numbers.
Ports can form an EtherChannel when they are in different PAgP modes as long as the modes are
compatible. For example:
compatible. For example:
•
A port in the desirable mode can form an EtherChannel with another port that is in the desirable or
auto mode.
auto mode.
•
A port in the auto mode can form an EtherChannel with another port in the desirable mode.
A port in the auto mode cannot form an EtherChannel with another port that is also in the auto mode
because neither port starts PAgP negotiation.
because neither port starts PAgP negotiation.
If your switch is connected to a partner that is PAgP-capable, you can configure the switch port for
nonsilent operation by using the non-silent keyword. If you do not specify non-silent with the auto or
desirable mode, silent mode is assumed.
nonsilent operation by using the non-silent keyword. If you do not specify non-silent with the auto or
desirable mode, silent mode is assumed.
Table 37-1
EtherChannel PAgP Modes
Mode
Description
auto
Places a port into a passive negotiating state, in which the port responds to PAgP packets
it receives but does not start PAgP packet negotiation. This setting minimizes the
transmission of PAgP packets. This mode is not supported when the EtherChannel
members are from different switches in the switch stack (cross-stack EtherChannel).
it receives but does not start PAgP packet negotiation. This setting minimizes the
transmission of PAgP packets. This mode is not supported when the EtherChannel
members are from different switches in the switch stack (cross-stack EtherChannel).
desirable Places a port into an active negotiating state, in which the port starts negotiations with other
ports by sending PAgP packets. This mode is not supported when the EtherChannel
members are from different switches in the switch stack (cross-stack EtherChannel).
members are from different switches in the switch stack (cross-stack EtherChannel).