Citrix Systems 6 User Manual
81
•
Use the host-list command to find the UUID of the host being configured:
xe host-list
Adding NIC bonds to an existing pool
Warning:
Do not attempt to create network bonds while HA is enabled. The process of bond creation
disturbs the in-progress HA heartbeating and causes hosts to self-fence (shut themselves
down); subsequently they will likely fail to reboot properly and you will need to run the host-
emergency-ha-disable command to recover them.
disturbs the in-progress HA heartbeating and causes hosts to self-fence (shut themselves
down); subsequently they will likely fail to reboot properly and you will need to run the host-
emergency-ha-disable command to recover them.
Note:
If you are not using XenCenter for NIC bonding, the quickest way to create pool-wide NIC
bonds is to create the bond on the master, and then restart the other pool members.
Alternately you can use the service xapi restart command. This causes the bond and VLAN
settings on the master to be inherited by each host. The primary management interface of
each host must, however, be manually reconfigured.
bonds is to create the bond on the master, and then restart the other pool members.
Alternately you can use the service xapi restart command. This causes the bond and VLAN
settings on the master to be inherited by each host. The primary management interface of
each host must, however, be manually reconfigured.
Follow the procedure in previous sections to create a NIC Bond, see
Configuring a dedicated storage NIC
You can use either XenCenter or the xe CLI to assign a NIC an IP address and dedicate it to a specific function, such
as storage traffic. When you configure a NIC with an IP address, you do so by creating a management interface.
IP-enabled NICs are referred to collectively as management interfaces. (The IP-enabled NIC XenServer used for
management is a type of management interface known as the primary management interface.)
as storage traffic. When you configure a NIC with an IP address, you do so by creating a management interface.
IP-enabled NICs are referred to collectively as management interfaces. (The IP-enabled NIC XenServer used for
management is a type of management interface known as the primary management interface.)
When you want to dedicate a management interface for a specific purpose, you must ensure the appropriate
network configuration is in place to ensure the NIC is used only for the desired traffic. For example, to dedicate a
NIC to storage traffic, the NIC, storage target, switch, and/or VLAN must be configured so that the target is only
accessible over the assigned NIC. If your physical and IP configuration do not limit the traffic that can be sent
across the storage management interface, it is possible for other traffic, such as management traffic, to be sent
across the storage NIC.
network configuration is in place to ensure the NIC is used only for the desired traffic. For example, to dedicate a
NIC to storage traffic, the NIC, storage target, switch, and/or VLAN must be configured so that the target is only
accessible over the assigned NIC. If your physical and IP configuration do not limit the traffic that can be sent
across the storage management interface, it is possible for other traffic, such as management traffic, to be sent
across the storage NIC.
Note:
When selecting a NIC to configure as a management interface for use with iSCSI or NFS SRs,
ensure that the dedicated NIC uses a separate IP subnet that is not routable from the primary
management interface. If this is not enforced, then storage traffic may be directed over the
main primary management interface after a host reboot, due to the order in which network
interfaces are initialized.
ensure that the dedicated NIC uses a separate IP subnet that is not routable from the primary
management interface. If this is not enforced, then storage traffic may be directed over the
main primary management interface after a host reboot, due to the order in which network
interfaces are initialized.
To assign NIC functions using the xe CLI
1.
Ensure that the PIF is on a separate subnet, or routing is configured to suit your network topology in order
to force the desired traffic over the selected PIF.
to force the desired traffic over the selected PIF.
2.
Setup an IP configuration for the PIF, adding appropriate values for the mode parameter and if using static
IP addressing the IP, netmask, gateway, and DNS parameters:
IP addressing the IP, netmask, gateway, and DNS parameters:
xe pif-reconfigure-ip mode=
<DHCP | Static>
uuid=
<pif-uuid>
3.
Set the PIF's disallow-unplug parameter to true:
xe pif-param-set disallow-unplug=true uuid=
<pif-uuid>
xe pif-param-set other-config:management_purpose="Storage" uuid=
<pif-uuid>