Jenn-Air W10394706A User Manual

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.

Check that all parts are included.

■

Gas pressure regulator

■

Burner grates

■

Burner bases and burner caps

■

Griddle drip tray (on griddle models)

■

Foam tape

■

LP orifice package (W10393255)

■

Conversion label (W10393342)

NOTE: The cooktop is manufactured for use with Natural gas. To 
convert to LP gas, see the “Gas Conversions” section.

48" (121.9 cm) models must be installed with a backsplash if 
installing at zero clearance to a combustible backwall. See 
“Cabinet Dimensions” in the “Location Requirements” section for 
installation requirements. 

■

36" (91.4 cm) Retractable Backguard
Order Part Number 8284756

■

48" (121.9 cm) Retractable Backguard
Order Part Number 8284755

■

9" (22.9 cm) Backguard for 36" (91.4 cm) Cooktops
Order Part Number W10115776

■

9" (22.9 cm) Backguard for 48" (121.9 cm) Cooktops
Order Part Number W10115777

■

33½" (85.0 cm) Retractable Backguard with Wire Shelf for 
36" (91.4 cm) Cooktops
Order Part Number W10285448

■

33½" (85.0 cm) Retractable Backguard with Wire Shelf for 
48" (121.9 cm) Cooktops
Order Part Number W10285449

To order, see the “Assistance or Service” section of the Use and 
Care Guide.

Check local codes and consult gas supplier. Check existing gas 
supply and electrical supply. See “Electrical Requirements” and 
“Gas Supply Requirements” sections.

To convert the cooktop for elevations above 6,560 ft (1999.5 m), 
order a High Altitude Conversion Kit.

■

Part Number W10394296 - LP high altitude

■

Part Number W10394295 - Natural gas high altitude

To order, see the “Assistance or Service” section of the Use and 
Care Guide.

IMPORTANT: Observe all governing codes and ordinances. Do 
not obstruct flow of combustion and ventilation air. 

■

It is the installer’s responsibility to comply with installation 
clearances specified on the model/serial rating plate. The 
model/serial rating plate is located on the underside of the 
cooktop burner base.

■

It is recommended that a 600 CFM or larger vent hood be 
installed above the cooktop. 

■

It is not recommended that a microwave hood combination 
be mounted above the cooktop.

■

The cooktop should be installed in a location away from 
strong draft areas, such as windows, doors and strong 
heating vents or fans.

■

All openings in the wall or floor where cooktop is to be 
installed must be sealed.

■

Cabinet opening dimensions that are shown must be used. 
Given dimensions are minimum clearances.

■

Grounded electrical supply is required. See “Electrical 
Requirements” section. 

■

Proper gas supply connection must be available. See “Gas 
Supply Requirements” section.

■

The cooktop is designed to hang from the countertop by its 
side or rear flanges.

■

The gas and electric supply should be located as shown in 
“Gas and Electric Connection Locations” section so that they 
are accessible without requiring removal of the cooktop.

■

Provide cutout in left rear corner of cutout enclosure as 
shown to provide clearance for gas inlet, power supply cord, 
and to allow the rating label to be visible.

IMPORTANT: To avoid damage to your cabinets, check with your 
builder or cabinet supplier to make sure that the materials used 
will not discolor, delaminate or sustain other damage.

The installation of this cooktop must conform to the 
Manufactured Home Construction and Safety Standard, Title 24 
CFR, Part 3280 (formerly the Federal Standard for Mobile Home 
Construction and Safety, Title 24, HUD Part 280). When such 
standard is not applicable, use the Standard for Manufactured 
Home Installations, ANSI A225.1/NFPA 501A or local codes.

In Canada, the installation of this cooktop must conform with the 
current standards CAN/CSA-A240-latest edition, or with local 
codes.

■

Adjustable wrench

■

Tape measure

■

Marker or pencil

■

Pipe wrench

■

Flat-blade screwdriver

■

¹⁵⁄₁₆" combination wrench 

■

Wrench or channel lock 
pliers

■

Pipe-joint compound 
resistant to LP gas

■

Noncorrosive leak-
detection solution

■

Adjustable wrench

■

³⁄₈" drive ratchet

■

½" deep-well socket

■

7 mm nut driver

■

Masking tape