Liebherr 120713 7082694 - 01 User Manual

q

Standard EN 378 specifies that the room in which you install

your  appliance  must  have  a  volume  of  1  m

2

  per  8  g  of  R

600a refrigerant used in the appliance. If the room in which

the  appliance  is  installed  is  too  small,  a  flammable  gas-air

mixture may form in the event of a leakage in the refrigera-

tion circuit. The quantity of refrigerant used in your appliance

is indicated on the type plate on the inside of the appliance.

q

Fit the appliance in stable kitchen units only.

q

The following ventilation gaps must be observed:

•

The depth of the ventilation channel at the rear of the unit

must be at least 38 mm.

•

There must be a ventilation space of at least 200 cm

2

 in

the plinth and at the top of the unit.

•

Basically  the  principle  applies:  the  larger  the  ventilation

space, the more energy-saving the appliance is in opera-

tion.

u

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

After installation:

u

Remove all transit supports.

u

Unscrew  the  red  transport

lock.  Close  the  vacated

retaining  hole  using  the

stopper (60).

u

u

Clean the appliance (see 6.2) .

If  the  appliance  is  installed  in  a  very  damp  environment,

condensate may form on the outside of the appliance.

u

Always see to good ventilation at the installation site.

Danger of suffocation due to packing material and plastic film!

u

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

-

corrugated board/cardboard

-

expanded polystyrene parts

-

polythene bags and sheets

-

polypropylene straps

-

nailed wooden frame with polyethylene panel*

u

Take the packaging material to an official collecting point.

Risk of damage to the electronic control system!

u

Do not use stand-alone inverters (conversion of d.c. to a.c./

three-phase) or energy saving plugs.

Fire and overheating hazard!

u

Do not use extension cables or multiple socket outlets.

The  type  of  current  (alternating  current)  and  voltage  at  the

installation site have to conform with the data on the type plate

(see Appliance at a glance).

The  socket  must  be  properly  earthed  and  fused.  The  tripping

current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can

be  quickly  disconnected  from  the  supply  in  an  emergency.  It

must be outside the area of the rear of the appliance.

u

Check the electrical connection.

u

Plug in the power plug.

u

Press On/Off button

 Fig. 2 (4)

.

w

The  temperature  display  flashes  until  the  temperature  is

sufficiently  cold.  If  the  temperature  is  above  0  °C,  dashes

flash. If it is below, the set temperature flashes.

You can adjust the brightness of the temperature display to the

light conditions of the room in which the appliance is installed.

The  brightness  is  adjustable  between 

h1

  (no  illumination)  and

h5

 (maximum luminosity).

u

To  activate  the  setting  mode:  press  the  SuperFrost  button

Fig. 2 (5)

 for about 5 s.

w The display indicates 

c

.

w

The SuperFrost button flashes.

u

Using  the  Up  setting  button

  Fig.  2  (3)

  or  Down  setting

button,

 Fig. 2 (2)

, select 

h

.

u

To confirm: briefly press the SuperFrost button

 Fig. 2 (5)

.

u

To  make  the  display  brighter:  press  Up  button

Fig. 2 (3)

.

u

To  make  the  display  darker:  press  Down  button

Fig. 2 (2)

.

u

To confirm: press SuperFrost button

 Fig. 2 (5)

.

w

The brightness is adjusted to the new value.

u

To  deactivate  the  set-up  mode:  press  On/Off  button

Fig. 2 (4)

.

u

Wait for 5 minutes.

w

The  temperature  is  indicated  again  in  the  temperature

display.

The  child-proofing  function  enables  you  to  make

sure that the appliance is not inadvertently switched

off by playing children.

u

To  activate  the  setting  mode:  press  SuperFrost  button

Fig. 2 (5)

 for about 5 s.

w The display indicates 

c

.

w

The button SuperFrost flashes.

u

Briefly press the SuperFrost button

 Fig. 2 (5)

 to confirm.

u

To switch on: Using the Up setting button

 Fig. 2 (3)

or Down setting button

 Fig. 2 (2)

, select 

c1

.

u

To switch off: Using the Up setting button, freezer

compartment

  Fig.  2  (3)

  or  Down  setting  button,

freezer compartment

 Fig. 2 (2)

, select 

c0

.

u

To confirm: press SuperFrost button

 Fig. 2 (5)

.