Liebherr 120713 7082694 - 01 User Manual

u

When the drawer is pulled out, hold down the On/Off button

(about 10 seconds).

w

After about 1 s the LED goes out, the IceMaker is switched

off.

w

After about 10 s the LED flashes for about 60 s.

u

Slide in the drawer while the LED is flashing.

w

The ice-cube tray of the IceMaker turns to a skew position.

u

Remove the drawer.

u

Clean the ice cube tray with warm water. If necessary, use

mild washing-up liquid. Then rinse.

Switch the IceMaker on again.

u

Press the ON/OFF button until the LED shines, then slide in

the drawer.

w

The IceMaker starts producing ice cubes.

If washing-up liquid was used:

u

throw away the first three loads of ice cubes to get rid of any

remaining washing-up liquid.

First check whether you can correct the fault yourself by refer-

ence to the list (see Malfunction). If this is not the case, please

contact  the  customer  service  whose  address  is  given  in  the

enclosed customer service list.

Risk of injury if repair work is not carried out professionally!

u

Have  any  repairs  and  action  -  not  expressly  specified  -  on

the  appliance  and  mains  cable  carried  out  by  service

personnel only. (see Maintenance)

u

Read  the  appliance

designation

Fig.  8  (1)

,  service

No.

  Fig.  8  (2)

  and

serial  No.

  Fig.  8  (3)

off  the  type  plate

located  inside  the

appliance on the left-

hand side.

Fig. 8 

u

Notify  the  customer  service,  specifying  the  fault,  appliance

designation

 Fig. 8 (1)

, service No.

 Fig. 8 (2)

 and serial No.

Fig. 8 (3)

.

w

This will help us to provide you with a faster and more accu-

rate service.

u

Keep  the  appliance  closed  until  the  customer  service

arrives.

w

The food will stay cool longer.

u

Pull out the mains plug (not by pulling the connecting cable)

or switch off the fuse.

Your  appliance  is  designed  and  manufactured  for  a  long  life

span  and  reliable  operation.  If  a  malfunction  nonetheless

occurs during operation, check whether it is due to a handling

error.  In  this  case  you  will  have  to  be  charged  for  the  costs

incurred, even during the warranty period. You may be able to

rectify the following faults yourself:
Appliance does not work.

→

The appliance is not switched on.

u

Switch on the appliance.

→

The power plug is not properly inserted in the wall socket.

u

Check power plug.

→

The fuse of the wall socket is not in order.

u

Check fuse.

→

The compressor switches to a low speed when little cold is

needed. Although the running time is increased as a result,

energy is saved.

u

This is normal in energy-saving models.

→

SuperFrost is activated.

u

The compressor runs for longer in order to rapidly cool the

food. This is normal.

→

The inverter is equipped with a diagnostic LED.

u

The flashing is normal.

→

Speed-controlled*  compressors  may  produce  varying

running noise due to different speed steps.

u

The sound is normal.

→

This noise comes from the refrigerant flowing in the refriger-

ation circuit.

u

The sound is normal.

→

The  noise  is  produced  whenever  the  refrigeration  unit

(motor) automatically switches on or off.

u

The sound is normal.

→

The  refrigeration  increases  automatically  when  the  Super-

Frost, function is activated, fresh food has just been placed

in the appliance or the door has been left open for a while.

u

The sound is normal.

→

The ambient temperature is too high.

u

→

The sound is produced by air flow noise of the fan.

u

The sound is normal.

→

The  noise  is  produced  when  the  door  is  opened  and

closed.

u

The sound is normal.

F0

F5

→

There is a fault.

u

Contact the customer service (see Maintenance).

nA

→

The freezer temperature rose too high over the last hours or

days due to a power failure or power interruption. When the

power  interruption  is  over,  the  appliance  will  continue  to

operate in the last temperature setting.

u

Press alarm button 

Fig. 2 (6)

w

The  highest  temperature  reached  during  power  failure  is

indicated in the temperature display for approx. 60 seconds.

The electronic unit then indicates the actual current freezing

temperature again.

u

To prematurely cancel the display of the warmest tempera-

ture: press alarm button

 Fig. 2 (6)

.

u

Check the quality of the food. Do not consume spoiled food.

Do not re-freeze thawed food.

→

The  appliance  and  therefore  the  IceMaker  are  not

connected.

u

Connect the appliance. (see Putting into operation).

→

The IceMaker is not switched on.

u

Switch on the IceMaker.

→

The drawer of the IceMaker is not properly closed.

u

Close the drawer properly.

→

The water connection is not open.