Toshiba 4511 User Manual
November 2003 © TOSHIBA TEC
5 - 55
e-STUDIO3511/4511 TROUBLESHOOTING
5.1.15 Laser optical unit related service call
[CA10] Polygonal motor abnormality
Is the polygonal motor rotating?
NO
1. Check if the connector CN352 on the LGC board is disconnected.
2. Check if the harness is open circuited or the connector pin is disconnected.
3. Check if the conductor pattern on the LGC board is short circuited or open
2. Check if the harness is open circuited or the connector pin is disconnected.
3. Check if the conductor pattern on the LGC board is short circuited or open
circuited.
4. Replace the laser optical unit.
5. Replace the LGC board.
5. Replace the LGC board.
YES
Is the printed image distorted?
Is the printed image distorted?
YES
1. Check if the connector CN352 on the LGC board is almost disconnected.
2. Check if the harness is almost open circuited or the connector pin is almost
2. Check if the harness is almost open circuited or the connector pin is almost
disconnected.
3. Check if the conductor pattern on the LGC board is short circuited or open
circuited.
4. Check if the laser unit cooling fan is stopped.
5. Check if the suction area of laser unit cooling fan is plugged up.
6. Replace the laser optical unit.
7. Replace the LGC board.
5. Check if the suction area of laser unit cooling fan is plugged up.
6. Replace the laser optical unit.
7. Replace the LGC board.
NO
1. Check if the conductor pattern on the LGC board is short circuited or open circuited.
2. Check if the units with high-voltage (developer unit, transfer belt unit and 2nd transfer roller unit)
1. Check if the conductor pattern on the LGC board is short circuited or open circuited.
2. Check if the units with high-voltage (developer unit, transfer belt unit and 2nd transfer roller unit)
are securely grounded.
3. Check if the bias supply joints of the units with high-voltage are securely connected or they are not
stained.
4. Check if the plate in paper transport system is securely grounded.
5. Check if the equipment is grounded.
6. Check if the laser unit cooling fan is stopped.
7. Check if the suction area of laser unit cooling fan is plugged up.
8. Replace the laser optical unit.
9. Replace the LGC board.
5. Check if the equipment is grounded.
6. Check if the laser unit cooling fan is stopped.
7. Check if the suction area of laser unit cooling fan is plugged up.
8. Replace the laser optical unit.
9. Replace the LGC board.
[CA20] H-Sync detection error
Is the cable (flexible flat type) between the connector (CN334) on the LGC board and connector (CN201)
on the LDR board open circuited, broken or disconnected?
on the LDR board open circuited, broken or disconnected?
YES
1. Reconnect the cable.
2. Check if the connector on the LGC board hold the cable securely.
3. Replace the laser optical unit.
2. Check if the connector on the LGC board hold the cable securely.
3. Replace the laser optical unit.
NO
1. Check if the units with high-voltage (developer unit, transfer belt unit and 2nd transfer roller unit) are
1. Check if the units with high-voltage (developer unit, transfer belt unit and 2nd transfer roller unit) are
securely grounded.
2. Check if the bias supply joints of the units with high-voltage are securely connected or they are not
stained.
3. Check if the plate in paper transport system is securely grounded.
4. Check if the equipment is grounded.
5. Check if the conductor pattern is short circuited or open circuited.
6. Replace the LGC board.
7. Replace the laser optical unit.
4. Check if the equipment is grounded.
5. Check if the conductor pattern is short circuited or open circuited.
6. Replace the LGC board.
7. Replace the laser optical unit.