Aten VE150 Quick Setup Guide
Systemvoraussetzungen
Konsolen
• Ein PC-kompatibler Computer mit VGA-Ausgang
• Zwei VGA, SVGA, XGA, SXGA oder Multisync-Monitore
• Zwei VGA, SVGA, XGA, SXGA oder Multisync-Monitore
Übersicht und Bedienung der Hardware
Vorderseitige Ansicht des VE-150L
Rückseitige Ansicht des VE-150L
Vorderseitige Ansicht des VE-150R
VE-150
VE-150 Video Extender User Guide
System Requirements
Consoles
• A PC compatible computer with a VGA output port
• Two VGA, SVGA, XGA, SXGA or Multisync monitors
• Two VGA, SVGA, XGA, SXGA or Multisync monitors
Hardware Overview and Operation
VE-150L Front View
VE-150L Rear View
VE-150R Front View
VE-150R Rear View
Hardware Installation
The numbers on the installation diagram indicate the order of steps to take to set up your
system.
system.
Important:
• Ensure that all equipment to be connected is powered off before beginning.
• To prevent damage to your installation, make sure that all devices are properly grounded.
• Power on the PCs and monitors only after following the numbered steps on the diagram.
• Category 5 UTP cable is not supplied with this package. It requires a separate purchase.
The cable can be up to 150m (500 feet) in length.
Gain Setting Table
Approximate distances only. Actually distances may vary by up to 10 meters. For optimal
display, please refer to the following display resolution and refresh rate settings: at 10 meters
use 1600 x 1200 60Hz, at 70m use 1280 x 1024 75Hz, at 150m use 1280 x 1024 60Hz. (These
settings are for reference only and may be affected by the type of monitor and graphic display
card used, as well as cable quality.)
display, please refer to the following display resolution and refresh rate settings: at 10 meters
use 1600 x 1200 60Hz, at 70m use 1280 x 1024 75Hz, at 150m use 1280 x 1024 60Hz. (These
settings are for reference only and may be affected by the type of monitor and graphic display
card used, as well as cable quality.)
Specifications
*DDC, DDC2 and DDC2B support is for the Local Monitor only.
Specifications
*Die Unterstützung von DDC, DDC2 und DDC2B ist nur für den lokalen Monitor erforderlich.
Rückseitige Ansicht des VE-150R
Hardware installieren
Die Zahlen im Installationsdiagramm entsprechen der Reihenfolge der Schritte, die zur
Installation durchgeführt werden müssen.
Installation durchgeführt werden müssen.
Wichtig:
• Schalten Sie zuerst alle anzuschließenden Geräte aus.
• Um eine Beschädigung Ihrer Geräte zu vermeiden, müssen alle Geräte ordnungsgemäß
geerdet sein.
• Schalten Sie die PCs und Bildschirme nur in der im Diagramm angegebenen Reihenfolge
ein.
• Das Kat.5-UTP-Kabel ist nicht im Lieferumfang enthalten. Sie müssen es separat erwerben.
Die Kabellänge darf maximal 150 m betragen.
Tabelle zur Pegeleinstellung
Diese Werte sind angenähert. Die tatsächlichen Entfernungen können um bis zu 10 m
variieren. Zur optimalen Anzeige, siehe die folgenden Empfehlungen für Auflösung und
Bildwiederholfrequenz: bei 10 m verwenden Sie 1600 x 1200 mit 60 Hz, bei 70 m 1280 x 1024
mit 75 Hz, bei 150 m verwenden Sie 1280 x 1024 mit 60 Hz. (Diese Werte sind rein orientativ
und können je nach verwendetem Monitor und Grafikkarte sowie der Kabelqualität variieren.)
variieren. Zur optimalen Anzeige, siehe die folgenden Empfehlungen für Auflösung und
Bildwiederholfrequenz: bei 10 m verwenden Sie 1600 x 1200 mit 60 Hz, bei 70 m 1280 x 1024
mit 75 Hz, bei 150 m verwenden Sie 1280 x 1024 mit 60 Hz. (Diese Werte sind rein orientativ
und können je nach verwendetem Monitor und Grafikkarte sowie der Kabelqualität variieren.)
VE-150Video Extender Guide de l’utilisateur
VE-150 Grafiksignal-Erweiterung
Especificaciones
*La prise en charge de DDC, DD C2 et DDC2B est uniquement pour l’écran local.
Requisitos del sistema
Consolas
• Un ordenador PC compatible con puerto VGA
• Dos monitores VGA, SVGA, XGA, SXGA o Multisync
• Dos monitores VGA, SVGA, XGA, SXGA o Multisync
Aspectos generales del hardware y del manejo
Vista frontal del VE-150L
Vista posterior del VE-150L
Vista frontal del VE-150R
Tabla de ajuste de ganancia
Distances approximatives uniquement : En effet les distances peuvent varier jusqu’à 10
mètres. Pour un affichage optimal, veuillez vous reporter aux paramètres de vitesse de
régénération et de résolution d'affichage : à 10 mètres, utilisez 1600 x 1200 à 60Hz, à 70 m
utilisez 1280 x 1024 à 75Hz et à 150 m utilisez 1280 x 1024 à 60Hz. (Ces paramètres servent
de référence uniquement et peuvent être affectés par le type d’écran et de carte graphique
utilisés, ainsi que la qualité du câble.)
mètres. Pour un affichage optimal, veuillez vous reporter aux paramètres de vitesse de
régénération et de résolution d'affichage : à 10 mètres, utilisez 1600 x 1200 à 60Hz, à 70 m
utilisez 1280 x 1024 à 75Hz et à 150 m utilisez 1280 x 1024 à 60Hz. (Ces paramètres servent
de référence uniquement et peuvent être affectés par le type d’écran et de carte graphique
utilisés, ainsi que la qualité du câble.)
VE-150 Extensión de vídeo Manual del usuario
#
Description
Function
1
PC Port
The VGA cable that connects to the computer’s
VGA port plugs in here.
VGA port plugs in here.
2
Monitor Port
The local monitor’s VGA cable plugs in here.
1
Setting
Category 5 UTP Cable Length (meters)
0
Not longer than 150
1
140-150
2
130-140
3
120-130
4
110-120
5
100-110
6
90-100
7
80-90
8
70-80
9
60-70
A
50-60
B
40-50
C
30-40
D
20-30
E
10-20
F
0-10
#
Description
Function
1
Remote I/O
The Category 5 UTP cable that connects this unit to
the Remote Unit plugs in here.
the Remote Unit plugs in here.
2
Power Jack
The Power Adapter cable plugs in here.
3
Power LED (top cover)
Lights to indicate that the unit is receiving power.
#
Description
Function
1
Monitor Port
The remote monitor’s VGA cable plugs in here.
#
Description
Function
1
Rotary Video Gain Switch
A 16 position rotary switch. Refer to the Gain Setting
Table to match the video gain setting to the
Category 5 cable length. Use a flathead screwdriver
or similar object to change the switch position.
Table to match the video gain setting to the
Category 5 cable length. Use a flathead screwdriver
or similar object to change the switch position.
2
Remote I/O
The Category 5 UTP cable that connects this unit to
the Local Unit plugs in here.
the Local Unit plugs in here.
3
Power Jack
The Power Adapter cable plugs in here.
4
Power LED (top cover)
Lights to indicate that the unit is receiving power.
Function
VE-150L
VE-150R
Computer Connection
1
N/A
Connectors
Console
Video
1 x HDB-15 female (blue)
Computer
Video
1 x HDB-15 male (blue)
N/A
Link
1 x RJ-45 socket
Power
1 x DC 5.3V jack
Switch
Video Gain
N/A
1 x 16 position switch
LEDs
Power
1 (orange)
Cable Length
150m (500') (max.)
Resolution
1280x1024, 60Hz DDC, DDC2, DDC2B*
Power Consumption
1.2W
1.2W
Operation Temperature
0~50˚C (0~80% RH, Non-condensing)
Storage Temperature
-20˚C~60˚C (0~80% RH, Non-condensing)
Housing
Metal
Weight
250 g
250 g
Dimensions
119 x 86 x 23 mm
119 x 86 x 23 mm
#
Beschreibung
Funktion
1
PC-Port
Hier wird das VGA-Kabel zum VGA-Ausgang des
Computers angeschlossen.
Computers angeschlossen.
2
Monitoranschluss
Hier schließen Sie das VGA-Kabel des lokalen
Bildschirms an.
Bildschirms an.
#
Beschreibung
Funktion
1
E/A zur Gegenstelle
Hier schließen Sie das UTP-Kabel der Kategorie 5 an,
das dieses Gerät mit dem der Gegenstelle verbindet.
das dieses Gerät mit dem der Gegenstelle verbindet.
2
Stromeingangs-
buchse
buchse
Hier schließen Sie das Stromkabel des Netzteils an.
3
LED-Betriebsanzeige
(obere Abdeckung)
(obere Abdeckung)
Leuchtet, wenn das Gerät mit Strom gespeist wird.
#
Beschreibung
Funktion
1
Monitoranschluss
Hier schließen Sie das VGA-Kabel des entfernten
Bildschirms an.
Bildschirms an.
#
Beschreibung
Funktion
1
Signalpegel-Drehregler
Ein 16-stufiger Drehregler. Um die richtige
E i n s t e l l u n g f ü r v e r s c h i e d e n e K a b e l l ä n g e n
h e r a u s z u f i n d e n , s i e h e d i e Ta b e l l e z u r
Pegeleinstellung. Drehen Sie den Regler mithilfe
eines Schraubendrehers oder mit einem ähnlichen
Gegenstand.
E i n s t e l l u n g f ü r v e r s c h i e d e n e K a b e l l ä n g e n
h e r a u s z u f i n d e n , s i e h e d i e Ta b e l l e z u r
Pegeleinstellung. Drehen Sie den Regler mithilfe
eines Schraubendrehers oder mit einem ähnlichen
Gegenstand.
2
E/A zur Gegenstelle
Hier schließen Sie das UTP-Kabel der Kategorie 5
an, das dieses Gerät mit dem lokalen verbindet.
an, das dieses Gerät mit dem lokalen verbindet.
3
Stromeingangs-buchse
Hier schließen Sie das Stromkabel des Netzteils an.
4
LED-Betriebsanzeige
(obere Abdeckung)
(obere Abdeckung)
Leuchtet, wenn das Gerät mit Strom gespeist wird.
Einstellung
Kabellänge (m) UTP Kat. 5
0
Nicht mehr als 150
1
140-150
2
130-140
3
120-130
4
110-120
5
100-110
6
90-100
7
80-90
8
70-80
9
60-70
A
50-60
B
40-50
C
30-40
D
20-30
E
10-20
F
0-10
Funktion
VE-150L
VE-150R
Verbindung zum Computer
1
_
Anschlüsse
Konsole
Bildschirm
1 x HDB-15 Weiblein (blau)
Computer
Bildschirm
1 x HDB-15
Männlein (blau)
_
Link
1 x RJ-45-Buchse
Stromversorgung
1 x Stromeingangsbuchse 5,3 V=
Switch
Signalpegeleinstellung
_
1 x Schalter mit
16 Stufen
LED-Anzeigen
Stromversorgung
1 (orange)
Kabellänge
150 m (max.)
Auflösung
1280 x 1024, 60Hz DDC, DDC2,
DDC2B*
Stromverbrauch
1.2W
1.2W
Betriebstemperatur
0~50˚C (0 - 80% rel. Luftfeuchte, nicht
kondensierend)
Lagertemperatur
-20˚C~60˚C (0 - 80% rel. Luftfeuchte,
nicht kondensierend)
Gehäuse
Metall
Gewicht
250 g
250 g
Abmessungen
119 x 86 x 23 mm
119 x 86 x 23 mm
Configuration système
Consoles
• Un ordinateur compatible PC avec un port de sortie VGA
• Deux moniteurs VGA, SVGA, XGA, SXGA ou Multisync
• Deux moniteurs VGA, SVGA, XGA, SXGA ou Multisync
Présentation du matériel et Fonctionnement
Vue Avant du VE-150L
Vue Arrière du 150L
Vue avant du VE-150R
Spécifications
*La prise en charge de DDC, DD C2 et DDC2B est uniquement pour l’écran local.
Vue Arrière du 150R
Installation du matériel
Les numéros sur le schéma d’installation indiquent l’ordre des étapes à suivre pour configurer
votre système.
votre système.
Important :
• Assurez-vous que tous les matériels à connecter sont hors tension avant de démarrer.
• Afin d’éviter d’endommager votre installation, vérifiez que tous les périphériques sont
• Afin d’éviter d’endommager votre installation, vérifiez que tous les périphériques sont
correctement reliés à la terre.
• Allumez les PC et les moniteurs uniquement après avoir suivi les étapes numérotées sur le
schéma.
• Le câble UTP de catégorie 5 n’est pas fourni dans cet emballage. Il doit être acheté
séparément. Le câble peut mesurer jusqu’à 150 m de long.
Tableau des paramètres de gain
Distances approximatives uniquement : En effet les distances peuvent varier jusqu’à 10
mètres. Pour un affichage optimal, veuillez vous reporter aux paramètres de vitesse de
régénération et de résolution d'affichage : à 10 mètres, utilisez 1600 x 1200 à 60Hz, à 70 m
utilisez 1280 x 1024 à 75Hz et à 150 m utilisez 1280 x 1024 à 60Hz. (Ces paramètres servent
de référence uniquement et peuvent être affectés par le type d’écran et de carte graphique
utilisés, ainsi que la qualité du câble.)
mètres. Pour un affichage optimal, veuillez vous reporter aux paramètres de vitesse de
régénération et de résolution d'affichage : à 10 mètres, utilisez 1600 x 1200 à 60Hz, à 70 m
utilisez 1280 x 1024 à 75Hz et à 150 m utilisez 1280 x 1024 à 60Hz. (Ces paramètres servent
de référence uniquement et peuvent être affectés par le type d’écran et de carte graphique
utilisés, ainsi que la qualité du câble.)
#
Description
Fonction
1
Port PC
Le câble VGA qui se connecte au port VGA de
l’ordinateur se branche ici.
l’ordinateur se branche ici.
2
Port moniteur
Le câble VGA du moniteur local se branche ici.
#
Description
Fonction
1
E/S distantes
Le câble UTP de catégorie 5 qui connecte cette unité à
l’unité distante se branche ici.
l’unité distante se branche ici.
2
Prise jack
d'alimentation
d'alimentation
Le câble de l’adaptateur secteur se branche ici.
3
Voyant d’alimentation
(cache supérieur)
(cache supérieur)
S’allume pour indiquer que l’unité reçoit du courant.
#
Description
Fonction
1
Port moniteur
Le câble VGA du moniteur distant se branche ici.
#
Description
Fonction
1
Commutateur de gain
vidéo rotatif
vidéo rotatif
Un commutateur rotatif à 16 positions. Reportez-
vous au Tableau des paramètres de gain pour
faire correspondre le paramètre de gain vidéo à
la longueur du câble de catégorie 5. Utilisez un
tournevis à tête fraisée ou un autre objet similaire
pour modifier la position du commutateur.
vous au Tableau des paramètres de gain pour
faire correspondre le paramètre de gain vidéo à
la longueur du câble de catégorie 5. Utilisez un
tournevis à tête fraisée ou un autre objet similaire
pour modifier la position du commutateur.
2
E/S distantes
Le câble UTP de catégorie 5 qui connecte cette
unité à l’unité locale se branche ici.
unité à l’unité locale se branche ici.
3
Prise jack d'alimentation
Le câble de l’adaptateur secteur se branche ici.
4
Voyant d’alimentation
(cache supérieur)
(cache supérieur)
S’allume pour indiquer que l’unité reçoit du courant.
Paramètre
Longueur de câble UTP de catégorie 5 (en mètres)
0
Pas plus de 150
1
140-150
2
130-140
3
120-130
4
110-120
5
100-110
6
90-100
7
80-90
8
70-80
9
60-70
A
50-60
B
40-50
C
30-40
D
20-30
E
10-20
F
0-10
Fonction
VE-150L
VE-150R
Connexion de l’ordinateur
1
Ne s’applique pas
Connecteurs
Console
Vidéo
1 x HDB 15 broches - femelle (bleu)
Ordinateur
Vidéo
1 x HDB 15 broches
- mâle (bleu)
Ne s’applique pas
Liaison
1 x prise RJ45
Alimentation
1 x prise jack CC 5,3 V
Commutateur
Gain vidéo
Ne s’applique pas
1 x commutateur à16
positions
Voyants
Alimentation
1 (orange)
Longueur de câble
150 m (max.)
Résolution
1280 x 1024, 60Hz DDC, DDC2, DDC2B*
Consommation électrique
1.2W
1.2W
Température de fonctionnement
de 0°C à 50°C (HR de 0 à 80 %, sans
condensation)
Température de conservation
de -20˚C à 60˚C (HR de 0 à 80 %, sans
condensation)
Boîtier
Métallique
Poids
250 g
250 g
Dimensions
119 x 86 x 23 mm
119 x 86 x 23 mm
#
Descripción
Función
1
Puerto PC
Aquí se conecta el cable VGA procedente del puerto
VGA del ordenador.
VGA del ordenador.
2
Puerto de monitor
Aquí se conecta el cable VGA del monitor local.
#
Descripción
Función
1
E/S remoto
Aquí se conecta el cable UTP de Categoría 5
procedente
de la unidad remota.
procedente
de la unidad remota.
2
Entrada de alimentación
A q u í s e c o n e c t a e l c a b l e d e l a d a p t a d o r d e
alimentación.
alimentación.
3
Indicador de alimentación
(tapa superior)
(tapa superior)
Se ilumina cuando la unidad está recibiendo corriente
eléctrica.
eléctrica.
#
Descripción
Función
1
Puerto de monitor
Aquí se conecta el cable VGA del monitor remoto.
V
ista posterior del VE-150R
Instalación del hardware
Los números del diagrama de instalación equivalen al orden de los pasos necesarios para
instalar el sistema.
instalar el sistema.
Importante:
• Apague todos los equipos que vaya a conectar.
• Para evitar daños en los dispositivos, verifique que todos ellos estén conectados a tierra
• Para evitar daños en los dispositivos, verifique que todos ellos estén conectados a tierra
correctamente.
• Encienda los PCs y los monitores sólo después de seguir los pasos exactamente en el
orden indicado en el diagrama.
• El cable UTP de categoría 5 no está incluido en el paquete. Deberá adquirirlo por separado.
Su longitud máxima puede ser de 150 m.
#
Descripción
Función
1
Dial de ganancia de vídeo
Dial de selección con 16 posiciones. Consulte
la Tabla de ajuste de ganancia para ajustarlo a
la longitud del cable de categoría 5. Emplee un
destornillador o un objeto similar para girarlo.
la Tabla de ajuste de ganancia para ajustarlo a
la longitud del cable de categoría 5. Emplee un
destornillador o un objeto similar para girarlo.
2
E/S remoto
Aquí se conecta el cable UTP de Categoría 5
procedente de la unidad local.
procedente de la unidad local.
3
Entrada de alimentación
Aquí se conecta el cable del adaptador de
alimentación.
alimentación.
4
Indicador de alimentación
(tapa superior)
(tapa superior)
Se ilumina cuando la unidad está recibiendo
corriente eléctrica.
corriente eléctrica.
Ajuste
Longitud del cable UTP de categoría 5 (metros)
0
Máximo 150
1
140-150
2
130-140
3
120-130
4
110-120
5
100-110
6
90-100
7
80-90
8
70-80
9
60-70
A
50-60
B
40-50
C
30-40
D
20-30
E
10-20
F
0-10
Función
VE-150L
VE-150R
Conexión al ordenador
1
_
Conectores
Consola
Pantalla
1 x HDB-15 hembra (azul)
Ordenador
Pantalla
1 x HDB-15 macho
(azul)
_
Enlace
1 x conector RJ-45
Alimentación
1 x toma de c.c. 5,3 V
Concen-trador
Ganancia de señal
de vídeo
_
1 conmutador
de 16 posiciones
Indicadores LED
Alimentación
1 (anaranjado)
Longueur de câble
150 m (max.)
Résolution
1280 x 1024, 60Hz DDC, DDC2, DDC2B*
Consumo
1.2W
1.2W
Temperatura de funcionamiento
0~50˚C (0 a 80% HR, sin condensar)
Temperatura de almacenamiento
-20˚C~60˚C (0 a 80% HR, sin condensar)
Carcasa
Metal
Peso
250 g
250 g
Dimensiones
119 x 86 x 23 mm
119 x 86 x 23 mm
The following contains information that relates to China:
www.aten.com
www.aten.com
www.aten.com
www.aten.com
8-Port Video Switch
© Copyright 2011 ATEN
®
International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other
trademarks are the property of their respective owners.
trademarks are the property of their respective owners.
This product is RoHS compliant.
Part No. PAPE-1223-162G
Printing Date: 02/2011
VS881
User Guide
A/V Over Cat 5 Extender
Patent No.
CN ZL 98252015.8
CN ZL 01124239.6
CN ZL 200410042772.8
US 7340556
US 7472217
CN ZL 98252015.8
CN ZL 01124239.6
CN ZL 200410042772.8
US 7340556
US 7472217
DE 29903667.7
DE 102004058233
TW 194030
TW 150098
TW I243890
DE 102004058233
TW 194030
TW 150098
TW I243890
US 6160543
US 6489854
US 7532998
JP 4160936
US 6489854
US 7532998
JP 4160936
VE-150
All information, documentation, and specifications contained in
this media are subject to change without prior notification by the
manufacturer. Please visit our website to find the most up to date
version.
version.
Online Registration
International:
http://support.aten.com
North America:
http://www.aten-usa.com/product_registration
http://support.aten.com
North America:
http://www.aten-usa.com/product_registration
Technical Phone Support
International:
886-2-86926959
North America:
1-888-999-ATEN Ext: 4988
United Kingdom:
44-8-4481-58923
886-2-86926959
North America:
1-888-999-ATEN Ext: 4988
United Kingdom:
44-8-4481-58923
FCC Information
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instruction manual,
may cause interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instruction manual,
may cause interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from
that which the receiver is connected;
• Consult the dealer/an experienced radio/television technician for
help.
A
B
Hardware Installation
Local Front View
Remote Front View
VGA Cable
Local PC
Local Front View
Remote Front View
Power Adapter Cable
Refer to Gain
Setting Table
for settings
Setting Table
for settings
VE-150L Front View
Hardware Review
VE-150R Front View
1
VE-150L Rear View
VE-150R Rear View
2
3
1
2
4
1
2
3
4
3
Cat 5 Cable
1
2
5
6
7
Package Contents
1 VE-150L (Local Unit)
1 VE-150R (Remote Unit)
1 VGA Cable (Part No.: LIN5-15X1-X2BG)
2 Power Adapters (DC 5.3V; 2.4A)
1 User Guide
1 VE-150R (Remote Unit)
1 VGA Cable (Part No.: LIN5-15X1-X2BG)
2 Power Adapters (DC 5.3V; 2.4A)
1 User Guide