Philips CMD310/05 Quick Setup Guide
EN
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product
at www.philips.com/welcome.
Read and understand all instructions before you use this product.
If damage is caused by failure to follow the instructions, the
warranty does not apply.
1 What’s in the box (Fig. 1)
1. Main unit and front panel
(with a sleeve)
2. Trim plate
3. ISO standard connector
4. Rubber cushion
5. Screw x 1
6. Disassembly tool x 2
7. User manual
8. Quick start guide
2 Connect wires (Fig. 2)
1
Check the car’s wiring carefully, and then connect them to
the supplied ISO wires. (Fig. 2 - 1)
the supplied ISO wires. (Fig. 2 - 1)
Connector
Connect to
1
Yellow wire
The +12V car battery which is live at all
times
2
Blue/White wire The electric antenna control lead or
power supply lead of the antenna
booster. If there is no electric antenna
or antenna booster, or it is manually
operated telescopic antenna, it is
unnecessary to connect this lead.
3
Black wire
A metal surface of the car. Connect
the black ground (earth) lead before
connecting the yellow and red power
supply leads.
4
Red wire
The +12V power terminal which is live
in the accessory (ACC) position of the
ignition switch. If there is no accessory
position, connect to the +12V car battery
terminal that is always live. Make sure
that the black ground (earth) lead is
connected to a metal surface of the car
first.
5
Green and
green/black wires
Left speaker (rear)
6
White and white/
black wires
Left speaker (front)
7
Gray and gray/
black wires
Right speaker (front)
8
Purple and
purple/black
wires
Right speaker (rear)
CMD310
All registered and unregistered trademarks are
property of their respective owners.
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
CMD310_05_QSG_V2.0
EN
Quick start guide
ES
Guía de configuación rápida
RU
Краткое руководство
Question?
Contact
Philips
RESET
MP3-LINK
4
5
RESET
d
c
a
Quick start guide
e
f
g
h
a
b
b
c
d
e
f
g
h
SUB-W
REAR LINE OUT
L
R
183 mm
53mm
5mm
183 mm
53.5 mm
1
3
2
2
Connect the other end of the supplied standard connector
to the car audio system. (Fig. 2 - 2)
to the car audio system. (Fig. 2 - 2)
Connector
Connect to
1
ANTENNA
Antenna for radio
2
External Mic
An external microphone for
phone call
3
SUBWOOFER (Socket)
Subwoofer
4
REAR LINE OUT L
(Socket)
Rear left speaker
5
REAR LINE OUT R
(Socket)
Rear right speaker
6
OE REMOTE (Brown)
OE remote
7
FRONT LINE OUT L
Front left speaker
8
FRONT LINE OUT R
Front right speaker
3 Mount into the dashboard
(Fig. 3)
If the car does not have an on-board drive or navigation
computer, disconnect the negative terminal of the car battery.
•
If you disconnect the car battery in a car that has an
on-board drive or navigation computer, the computer
may lose its memory.
on-board drive or navigation computer, the computer
may lose its memory.
•
If the car battery is not disconnected, to avoid short-
circuit, make sure that the bare wires do not touch
each other.
circuit, make sure that the bare wires do not touch
each other.
1
Make sure that the car dashboard opening is within the
indicated measurements. (Fig. 3 - 1)
indicated measurements. (Fig. 3 - 1)
2
Install the sleeve into the dashboard and bend the tabs
outwards to fix the sleeve. (Fig. 3 - 2)
outwards to fix the sleeve. (Fig. 3 - 2)
Note
•
If the system is not fixed by sleeve but by the supplied
screws, skip this step.
3
Place the supplied rubber cushion over the end of the
mounting bolt. (Fig. 3 - 3)
mounting bolt. (Fig. 3 - 3)
4
Slide the system into the dashboard until you hear a “click”.
(Fig. 3 - 4)
(Fig. 3 - 4)
5
Attach the trim plate. (Fig. 3 - 5)
6
Reconnect the negative terminal of the car battery.
4 Turn on
Press
.
»
[WELCOME] scrolls.
•
To turn off the system, press and hold
until
[GOODBYE] is displayed.
5 Set the clock
1
Press and hold to access the system menu.
2
Press repeatedly until [CLOCK] and the current time
are displayed.
are displayed.
»
If the clock is not set before, [00:00] is displayed.
3
Rotate
to set the hour.
4
Press
to confirm.
5
Rotate
to set the minute.
6
Press
to confirm.
6 Select a source
Note
•
When all other sources are unavailable, the system switches
the source to [RADIO] automatically.
Press
repeatedly to select a source.
•
[RADIO]: FM/AM radio
•
[MP3-LINK]: the audio input through the MP3-LINK socket
•
[BT AUDIO]: the audio transferred from a Bluetooth
device
device
•
[USB]: When a USB storage device is connected and
recognized, you can select this source to play audio files that
are stored on it.
recognized, you can select this source to play audio files that
are stored on it.
•
[iPHONE]: When an iPhone or iPod touch is connected
and recognized, you can select this source to play the
playlist of iPhone or iPod touch.
and recognized, you can select this source to play the
playlist of iPhone or iPod touch.
7 Listen to radio
Select a radio region
You can select a radio region that matches your location.
1
Press and hold to access the system menu.
2
Press repeatedly until [AREA] is displayed.
3
Rotate
to select an option.
•
[USA] (United States)
•
[EUR] (Western Europe)
•
[RUS] (Russia)
•
[AUS] (Australia)
•
[EAS] (Middle East)
•
[ASI] (Asia Pacific)
•
[JAP] (Japan)
•
[LAT] (Latin America)
CLICK
6