GE JKP75 Specification Guide
JKP75BM/WM
GE
®
27" Built-In Convection/Thermal Wall Oven
For answers to your Monogram,
®
GE Profile
™
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Listed by
Underwriters
Laboratories
320362
Specification Created 9/06
Note: Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least a 194°F
temperature rating.
Note: If marks, blemishes or the cutout opening is
Note: If marks, blemishes or the cutout opening is
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or openings are covered.
Note: Door handle protrudes 3" from door face.
Note: Door handle protrudes 3" from door face.
Cabinets and drawers on adjacent 45° and 90° walls
should be placed to avoid interference with the handle.
KW Rating
240V
6.8
208V
5.1
Breaker Size
240V
30 Amps
208V
30 Amps
Electric wall ovens are not approved for installation
with a plug and receptacle. They must be hard wired
in accordance with installation instructions.
Dimensions and Installation Information (in inches)
Cabinet
27"
A – Cabinet width required
27" min.
B – Minimum cabinet depth
23-5/8"
C – Opening width
25" min. - 25-1/4" max
D – Opening height
50-1/8" max
E – Recommended minimum cutout location from floor
13-1/4"
Oven
F – Overall depth*
F – Overall depth*
23-5/8"
G – Overall height with trim
51-7/8" - 52-3/4"
Overall height without trim
51"
H – Overall width
26-5/8"
*Depth including door handle is approximately 26-7/10" min. to 26-8/10" max.
CL
Suitable
bracing
to support
runners
18"
Over centerline
of cabinet
(must support 300 lbs.)
2" x 4" or
equivalent
runners
10
Locate
junction box
for 27"models
either 5" MIN.
below cutout
floor or 44"
MIN. above
cutout floor
Access
from
adjacent
cabinet
required
Allow 3/4"
for overlap
over all edges
of cutout
A
Minimum
cutout location
from floor
D
E
2" X 4" or
equiv. runners
(cutout floor)
21" MIN.
door opening
allowance
B
C
H
F
G
Locate
junction box
for 24"models
56" MIN. above
cutout floor
Conduit
(48-1/2" Long)
21
Cabinet
27"
A – Cabinet width required
27" min.
B – Minimum cabinet depth
23-5/8"
C – Opening width
25" min. - 25-1/4" max
D – Opening height
50-1/8" max
E – Recommended minimum cutout location from floor
13-1/4"
Oven
F – Overall depth*
F – Overall depth*
23-5/8"
G – Overall height with trim
51-7/8" - 52-3/4"
Overall height without trim
51"
H – Overall width
26-5/8"
*Depth including door handle is approximately 26-7/10" min. to 26-8/10" max.
CL
Suitable
bracing
to support
runners
18"
Over centerline
of cabinet
(must support 300 lbs.)
2" x 4" or
equivalent
runners
10
Locate
junction box
for 27"models
either 5" MIN.
below cutout
floor or 44"
MIN. above
cutout floor
Access
from
adjacent
cabinet
required
Allow 3/4"
for overlap
over all edges
of cutout
A
Minimum
cutout location
from floor
D
E
2" X 4" or
equiv. runners
(cutout floor)
21" MIN.
door opening
allowance
B
C
H
F
G
Locate
junction box
for 24"models
56" MIN. above
cutout floor
Conduit
(48-1/2" Long)
21