NAD C715 User Guide

23. Battery Disposal - When disposing of used batteries, please comply 

with governmental regulations or environmental public instruction’s 
rules that apply in your country or area.

24. Safety Check - Upon completion of any service or repairs to this 

product, ask the service technician to perform safety checks to 
determine that the product is in proper operating condition. 

25. Wall or Ceiling Mounting - The product should be mounted to a wall 

or ceiling only as recommended by the manufacturer.

The lightning flash with arrowhead symbol, within an 
equilateral triangle, is intended to alert the user to the presence 
of uninsulated “dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude to constitute a 
risk of electric shock to persons

The exclamation point within an equilateral triangle is intended 
to alert the user to the presence of important operating 
and maintenance (servicing) instructions in the literature 
accompanying the appliance.

 

ThE APPARATUS ShoUlD bE INSTAllED NEAR To AN EASIly ACCESSIblE 
SoCkET-oUTlET.

CAUTION
The C 715 employs a laser System. To ensure proper use of this product, 
please read this owner’s manual carefully and retain for future reference. 
Should the unit require maintenance, contact an authorized service 
location. Use of controls, adjustments or the performance of procedures 
other than those specified may result in exposure to laser radiation. To 
prevent direct exposure to laser beam, do not try to open the enclosure. 
Visible laser radiation when the enclosure is opened.
DO NOT STARE INTO BEAM.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a 
Class b digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation.

This equipment generates, uses and can radiate radio frequency energy and if 
not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. however, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected

•  Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING
Changes or modifications not expressly approved by the party responsible 
for compliance could void the user’s authority to operate the equipment.

INDUSTRY CANADA REQUIREMENT
This Class b digital apparatus meets all requirements of the Canadian 
Interference-Causing Equipment Regulations.

CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit 
(from the largest outer dimensions including projections) than is equal to, 
or greater than shown below. 
 left and Right Panels: 10 cm 
 Rear Panel: 10 cm 
 Top Panel: 50 cm 

IMPORTANT INFORMATION TO UK CUSTOMERS
DO NOT cut off the mains plug from this equipment. If the plug fitted is not 
suitable for the power points in your home or the cable is too short to reach 
a power point, then obtain an appropriate safety approved extension lead 
or consult your dealer. If nonetheless, the mains plug is cut off, REMoVE 
ThE FUSE and dispose of the PlUG immediately, to avoid possible shock 
hazard by inadvertent connection to the mains supply. If this product is 
not provided with a mains plug, or one has to be fitted, then follow the 
instructions given below: 

IMPORTANT
DO NOT make any connection to the larger terminal which is marked 
with the letter ‘E’ or by the safety earth symbol or colored GREEN or GREEN 
AND yElloW. The wires in the mains lead on this product are colored in 
accordance with the following code: 
 blUE - NEUTRAl 
 bRoWN - lIVE 

As these colors may not correspond with the colored markings identifying 
the terminals in your plug, proceed as follows: 
•  The blUE wire must be connected to the terminal marked with the 

letter ‘N’ or colored blACk. 

•  The bRoWN wire must be connected to the terminal marked with the 

letter ‘l’ or colored RED 

•  When replacing the fuse, only a correctly rated and approved type 

should be used, and be sure to re-fit the fuse cover.