Mitsubishi lt-3280 Owner's Manual
Chapter 2: Connecting
24
Antenna or Wall Outlet Cable to a VCR
Figure 8
A two-way RF splitter, 3 coaxial cables, right and left audio cables and a S-Video or (Composite) Video cables are required. These
are not included with the media center.
1. Connect the incoming cable or Antenna to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR rear panel.
3. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the media center rear panel.
4. To use the display’s internal speakers with the VCR, connect a Left/Right set of audio cables from AUDIO OUT on
the VCR rear panel to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the media center rear panel. The red
cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono
(non-stereo), connect only the white (left) cable.
cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono
(non-stereo), connect only the white (left) cable.
5. Connect either an S-Video or Video cable from VIDEO OUT on the VCR rear panel to INPUT-1 VIDEO on the media
center rear panel. Only one type of video cable should be connected. S-Video is recommended, if available.
6. For NetCommand® controlled recordings, connect a set of audio cables from AUDIO IN on the VCR rear panel
to MONITOR OUTPUT AUDIO-LEFT (MONO) and AUDIO-RIGHT on the media center rear panel. The red cable
connects to the R (right) channel and the white cable connects to the L (left) channel.
connects to the R (right) channel and the white cable connects to the L (left) channel.
7. Complete the NetCommand controlled recordings connections by connecting a Video cable from VIDEO IN on the
VCR rear panel to MONITOR OUTPUT on the media center rear panel.
Note: NetCommand® will assume your VCR is connected to inputs as shown on this page. If you use any
other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
Figure 8. Connecting a VCR to an Antenna or Wall Outlet Cable
*/
065
065
580
8
"
:
41-*55&3
*ODPNJOH
$BCMF
$BCMF
7$3CBDLQBOFM
*GZPVS7$3IBTBWJEFPDIBOOFM
PS3'0/0''TXJUDI TFUJUUP
0''
PS3'0/0''TXJUDI TFUJUUP
0''
)46
7*%&0
7*%&0
"6%*0
3
-.0/0
47*%&0
47*%&0
*/
065
"6%*0
3
-
5*.&33&4&5
"$5*7&"7/&5803,
$0/7&35&3
#09$0/530-
#09$0/530-
*/
065
47JEFPSFDPNNFOEFEJGBWBJMBCMF
"UUBDIPOMZPOFWJEFPDBCMFUZQF
47JEFPPS $PNQPTJUF
7JEFP
*/
065
*/
065
*/
7$3
.FEJB$FOUFS
4QMJUUFS
*/
Note: With this connection configuration, it is possible to view live cable programs through the VCR. For
best picture quality, however, always view live cable programs directly from the cable box (connected to
ANT-1) instead of the VCR.
best picture quality, however, always view live cable programs directly from the cable box (connected to
ANT-1) instead of the VCR.