Mitsubishi lt-3280 Owner's Manual
Chapter 3: NetCommand® Setup and Editing
40
A/V Receiver Learn Screen
Figure 10
1. Press
ADJUST or on the TV remote to select the
check box for each function to be learned.
2. Press ENTER and the function name will begin to
flash to confirm the ready-to-learn status.
3. Press the button on the A/V receiver’s remote control
that corresponds to the selected function, A check
mark will appear and the function name will stop
flashing. This confirms the signal learned status.
mark will appear and the function name will stop
flashing. This confirms the signal learned status.
4. To test the learned command, press ENTER on the
TV remote control. The A/V receiver will perform
the selected function. The A/V receiver needs to be
turned on and the IR emitters properly placed for
the test to be successful (see page 30 for IR emitter
placement).
the selected function. The A/V receiver needs to be
turned on and the IR emitters properly placed for
the test to be successful (see page 30 for IR emitter
placement).
5. Repeat for each function to be learned.
6. To erase a learned function, highlight the check box
for that function and press CANCEL.
7. When the function signals have been learned, press
ADJUST to select Next> and move to the Name
screen.
screen.
If the number of connected inputs changes, you will need
to delete the A/V receiver through Edit NetCommand and
add it again, as described above.
to delete the A/V receiver through Edit NetCommand and
add it again, as described above.
Figure 8. A/V Receiver Input screen
Figure 10. A/V receiver Learn screen
Hint: If your A/V receiver remote control uses a single
button for both Power On and Power Off, don’t learn the
Power Off function. If your A/V receiver uses a single
button to toggle between digital and analog sound,
then learn only Analog to Digital. If your A/V receiver
automatically switches between analog and digital audio,
then you don’t need to learn either Analog to Digital or
Digital to Analog functions
Power Off function. If your A/V receiver uses a single
button to toggle between digital and analog sound,
then learn only Analog to Digital. If your A/V receiver
automatically switches between analog and digital audio,
then you don’t need to learn either Analog to Digital or
Digital to Analog functions
.
A/V Receiver Input Learn Screen
Figure 9
Figure 9. A/V receiver Input Learn screen
NetCommand can now learn the remote control signals used to
select each input on the A/V receiver.
select each input on the A/V receiver.
1. Press ADJUST or on the TV remote control to select the
check box for each function to be learned.
2. Press ENTER and the function name will begin to flash to
confirm the ready-to-learn status.
3. Point the A/V receiver’s remote control at the display. If
close to the screen, see page 10 for the location of the
Learning IR sensor. Press the button on the remote control
that corresponds to the selected function. A check mark
will appear and the function name will stop flashing. This
confirms the signal learned status.
Learning IR sensor. Press the button on the remote control
that corresponds to the selected function. A check mark
will appear and the function name will stop flashing. This
confirms the signal learned status.
4. To test the learned command, while the function is selected,
press ENTER on the TV remote control. The A/V receiver will
perform the selected function. The A/V receiver needs to be
turned on and the IR emitters properly placed for the test to
be successful (see page 30 for IR emitter placement).
perform the selected function. The A/V receiver needs to be
turned on and the IR emitters properly placed for the test to
be successful (see page 30 for IR emitter placement).
5. To customize the input names, press ADJUST to move to
the Input Name text box and then press ADJUST
or
and ENTER to select each letter of the name. These names
will appear on the Review screen as the A/V receiver’s input
names.
will appear on the Review screen as the A/V receiver’s input
names.
6. To erase the learned input signal, highlight the check box for
that input and press CANCEL.
7. Repeat for each connected input.
8. When the input selection signals have been learned and the
inputs named, press ADJUST to select Next> and move
to the A/V receiver Learn screen.
to the A/V receiver Learn screen.