Mitsubishi 2040u User Manual
- 19 -
ENGLISH
No operation of
the USB devices
the USB devices
PROBLEM
ITEMS TO CHECK
Before calling your Authorized Product Support, please
check that the items below are properly connected or set.
In case of using a non-standard signal, please check the
pin assignments and the signal timing of your computer
with the specification outlined in Section 6. SPECIFICA-
TIONS and Section 7. APPENDIX.
check that the items below are properly connected or set.
In case of using a non-standard signal, please check the
pin assignments and the signal timing of your computer
with the specification outlined in Section 6. SPECIFICA-
TIONS and Section 7. APPENDIX.
LOCATION
No
picture
picture
LED On
(Green)
(Green)
Contrast and brightness controls.
Power switch.
AC power cord disconnected.
AC power cord disconnected.
Signal cable disconnected.
BNC cables are misconnected or the green cable is discon-
nected.
Computer power switch.
Power management function is active.
BNC cables are misconnected or the green cable is discon-
nected.
Computer power switch.
Power management function is active.
Signal cable disconnected.
BNC cables are misconnected or the green cable is discon-
nected.
Computer power switch.
Power management function is active.
BNC cables are misconnected or the green cable is discon-
nected.
Computer power switch.
Power management function is active.
Input signal frequency range is too high or too low for the
monitor to synchronize with.
monitor to synchronize with.
Do "GEOMETRY-RESET" or "ALL RESET" for a standard signal.
Adjust HORIZ-SIZE, VERT-SIZE, HORIZ-PHASE, and
VERT-POSITION with non-standard signals.
Monitor may not be able to get full-screen image depend on
signal. In this case, please select other resolution, or other
vertical refresh timing.
Make sure you wait a few seconds after adjusting the size
of the image before changing or disconnecting the signal.
Adjust HORIZ-SIZE, VERT-SIZE, HORIZ-PHASE, and
VERT-POSITION with non-standard signals.
Monitor may not be able to get full-screen image depend on
signal. In this case, please select other resolution, or other
vertical refresh timing.
Make sure you wait a few seconds after adjusting the size
of the image before changing or disconnecting the signal.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Front (OSD)
Front
Rear
Rear
Rear
Check the graphics adapter and cables
Computer
Press any key on the keyboard
or move the mouse.
Check the graphics adapter and cables
Computer
Press any key on the keyboard
or move the mouse.
Rear
Check the graphics adapter and cables
Computer
Press any key on the keyboard
or move the mouse.
Check the graphics adapter and cables
Computer
Press any key on the keyboard
or move the mouse.
Check the specification of
graphics adapter
graphics adapter
Front (OSD)
Front (OSD)
Front (OSD)
Abnormal picture
Display is miss-
ing, center shifts,
or too small or too
large of a display
size
ing, center shifts,
or too small or too
large of a display
size
ATTENTION
ATTENTION
PLEASE CHANGE
PLEASE CHANGE
SIGNAL TIMING.
SIGNAL TIMING.
SIGNAL TIMING.
SIGNAL FREQUENCY
SIGNAL FREQUENCY
IS OUT OF RANGE.
IS OUT OF RANGE.
IS OUT OF RANGE.
FH
FH
24.8KHz FV
24.8KHz FV 43.0Hz
43.0Hz
H OFF V OFF
H OFF V OFF
PLEASE
PLEASE CHECK
CHECK
INPUT
INPUT SIGNAL
SIGNAL OR
OR
CONNECTION.
CONNECTION.
ATTENTION
ATTENTION
NO SIGNAL
NO SIGNAL
The following message appeared.
The following message appeared.
[Universal serial bus controller] is not listed in [Device
Manager].
Manager].
[Generic USB HUB] is not listed in [Device Manager].
On the OSD screen, the Upstream port to which the
USB device you want to use is connected is not
colored by blue.
USB device you want to use is connected is not
colored by blue.
Confirm that Windows98 is in-
stalled into the computer.
stalled into the computer.
Make sure of the cable con-
nections.
Restart the computer.
Turn off the monitor and turn
on then.
Disconnect all the cables con-
nected to theUpstream ports
and re-connect then.
nections.
Restart the computer.
Turn off the monitor and turn
on then.
Disconnect all the cables con-
nected to theUpstream ports
and re-connect then.
Select the Upstream port by
using the OSD screen, "Up-
stream port selection"
using the OSD screen, "Up-
stream port selection"
5
5
TROUBLESHOOTING
LED Off
LED On
(Amber)
(Amber)