Pelco ie10c-1 Specification Guide
TECHNICAL SPECIFICATIONS
GENERAL
Imaging Device
1/3-inch (effective)
Imager Type
CMOS
Imager Readout
Progressive scan
Maximum Resolution
1280 x 1024
Signal-to-Noise Ratio
50 dB
Auto Iris Lens Type
DC drive
Electronic Shutter Range
1 ~ 1/100,000 sec
Wide Dynamic Range
60 dB
White Balance Range
2,000° to 10,000°K
Sensitivity
f/1.2; 2850°K; SNR >24 dB
Color (1x/33 ms)
0.5 lux
Color SENS (15x/500 ms)
0.12 lux
Mono (1x/33 ms)
0.25 lux
Mono SENS (15x/500 ms)
0.03 lux
Dome Attenuation
Clear
Zero light loss
Smoked
f/1.0 light loss
Construction
Cast aluminum body with polycarbonate
bubble
bubble
Finish
Light gray powder coated
Weight (without lens)
Unit
1.5 kg (3.3 lb)
Shipping
2.3 kg (5.0 lb)
Available Languages
Chinese, English, French, German, Italian,
Portuguese, Russian, Spanish, and Turkish
ELECTRICAL
Port
RJ-45 connector for 100Base-TX
Auto MDI/MDI-X
Auto MDI/MDI-X
Cable Type
Cat5 or better for 100Base-TX
Power Input
18 to 30 VAC; 24 VAC nominal or
PoE (IEEE 802.3af class 3)
PoE (IEEE 802.3af class 3)
Power Consumption*
<7 W; <40 W with heater operation
Current Consumption
PoE
<140 mA maximum
24 VAC
†
<510 mA without heater operation;
<2.5 A maximum with heater operation
<2.5 A maximum with heater operation
Local Storage
Micro SD
Alarm Input
10 VDC maximum, 5 mA maximum
Alarm Output
0 to 15 VDC maximum, 75 mA maximum
Service Port
External 3-connector, 2.5 mm provides
NTSC/PAL video output
NTSC/PAL video output
Accessory Port
Connects Pelco accessories
Audio
Bidirectional: half duplex
Line level/external microphone input;
600 Ohm differential,
1 Vp-p max signal level
Line level/external microphone input;
600 Ohm differential,
1 Vp-p max signal level
Compression
G.711 PCM 64 kbit/s
*Does not include optional devices connected to the accessory port
†
Required for heater operation
MECHANICAL
Lens Mount
CS mount, adjustable
Pan/Tilt Adjustment
Pan
368°
Tilt
160° (10° to 170°)
Rotate
355°
ENVIRONMENTAL
Operational Temperature
–30° to 50°C (–22° to 122°F); PoE operates
between 0° to 50°C (32° to 122°F), 24 VAC
power is required for heater operation below
0°C (32°F)
power is required for heater operation below
0°C (32°F)
Thermostat Operation
Heater thermostatically controlled to operate
below <5°C (<41°F)
Operational Humidity
20% to 80%, noncondensing
IMPACT RESISTANCE
Impact Resistance
IK10++ per EN62262 (70J)
NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
18.92
(7.45)
8.28
(3.26)
IN-CEILING
19.51
(7.68)
15.95
(6.28)
SURFACE MOUNT
(Mounting Ring Is Available as an Accessory)
(Mounting Ring Is Available as an Accessory)
19.38
(7.63)
20.32
(8.00)
Ø 12.70
(5.00)
(5.00)
PENDANT
(Mount Is Available as an Accessory)
(Mount Is Available as an Accessory)