Ken-A-Vision x2000 User Manual
9. Rotate the lens turret (item #10) to select the right lens for ideal viewing.
10. The greater the magnification the darker the room should be.
10. The greater the magnification the darker the room should be.
HORIZONTAL PROJECTION
1. Holding the neck of the microprojector with your left hand, place your
right hand around the back of the dust proof revolving disk (item #14 avail-
able on X-1000-1 only) and pull the projecting mechanism up into the hori-
zontal position
2. When using liquids and projecting horizontally, the instrument head must
be placed in a vertical position. Bring the specimen into focus while in the
vertical position, then move the mirror (item# 15) into the light path and
adjust so the image appears on the screen. Select the lens desired and refocus.
right hand around the back of the dust proof revolving disk (item #14 avail-
able on X-1000-1 only) and pull the projecting mechanism up into the hori-
zontal position
2. When using liquids and projecting horizontally, the instrument head must
be placed in a vertical position. Bring the specimen into focus while in the
vertical position, then move the mirror (item# 15) into the light path and
adjust so the image appears on the screen. Select the lens desired and refocus.
LIGHT POLARIZATION
1. Rotate the polarizing lens/analyzer (item #6 - white) until the lens is
beneath the light beam.
2. Rotate the dust proof revolving disk (item #14) until the RED “P” on the
edge of the disk is directly below the RED line.
3. Place a slide containing polarizing material on the stage.
4. Bring into focus and change colors by turning the polarizing lens/analyz-
er. (item #5)
beneath the light beam.
2. Rotate the dust proof revolving disk (item #14) until the RED “P” on the
edge of the disk is directly below the RED line.
3. Place a slide containing polarizing material on the stage.
4. Bring into focus and change colors by turning the polarizing lens/analyz-
er. (item #5)
USE AS A MICROSCOPE
(X-1000-1 only)
1. Rotate the auxiliary lens disk (item #14) until the RED “E” on the edge
of the disk is directly below the RED line.
2. Rotate the light diffusing lens (item #5-darker lens) until it is under the
light beam.
3. Place the unit in the horizontal position.
4. View the specimen through the 10X eyepiece tube (item #16).
5. Bring into focus using the 16mm lens; then select the lens desired.
of the disk is directly below the RED line.
2. Rotate the light diffusing lens (item #5-darker lens) until it is under the
light beam.
3. Place the unit in the horizontal position.
4. View the specimen through the 10X eyepiece tube (item #16).
5. Bring into focus using the 16mm lens; then select the lens desired.
MODEL TRIG
OPERATING INSTRUCTIONS
Instructions covering the use of Ken-A-Vision Microprojector Model X1000-
1 apply except for the following:
1. Under “Vertical Projection” instructions disregard #4. Model Trig has only
one objective lens.
2. Under “Vertical Projection” instructions disregard #7 entirely. Turning
the knob between the two mounting rods adjusts the focus.
3. Under “Vertical Projection” disregard #9 in its entirety.
4. Instructions for the light polarization and use as a microscope are the same as for
Model X1000-1
1 apply except for the following:
1. Under “Vertical Projection” instructions disregard #4. Model Trig has only
one objective lens.
2. Under “Vertical Projection” instructions disregard #7 entirely. Turning
the knob between the two mounting rods adjusts the focus.
3. Under “Vertical Projection” disregard #9 in its entirety.
4. Instructions for the light polarization and use as a microscope are the same as for
Model X1000-1
MODEL TECH A-11
OPERATING INSTRUCTIONS
VERTICAL PROJECTION
1. Turn the switch to the “ON” position.
2. Place a white sheet of paper between the legs of the base.
3. Rotate lenses (item#5 and #6), polarizing lens (item#14) 5X Wide Field auxiliary
lens (item #15), and the mirror (item #16) so the light beam will not be obstructed.
4. Rotate the revolving lens turret (item#10) containing the three lenses, until the
16mm lens (item#11) is positioned so the light beam penetrates it.
5. Place a specimen slide on the stage (item#8), and center it under the light.
6. Turn the focusing knob (item#9) and lower the stage (item#8) to the lowest posi-
tion;then reverse the direction until the specimen is brought into focus.
7. To use the 5X Wide Field Auxiliary lens (item#15), move it directly under the
light beam. It can be used with any of these lenses.
8. Rotate the lens turret (item#10) to select the proper lens for ideal viewing.
9. The greater the magnification the darker the room should be.
2. Place a white sheet of paper between the legs of the base.
3. Rotate lenses (item#5 and #6), polarizing lens (item#14) 5X Wide Field auxiliary
lens (item #15), and the mirror (item #16) so the light beam will not be obstructed.
4. Rotate the revolving lens turret (item#10) containing the three lenses, until the
16mm lens (item#11) is positioned so the light beam penetrates it.
5. Place a specimen slide on the stage (item#8), and center it under the light.
6. Turn the focusing knob (item#9) and lower the stage (item#8) to the lowest posi-
tion;then reverse the direction until the specimen is brought into focus.
7. To use the 5X Wide Field Auxiliary lens (item#15), move it directly under the
light beam. It can be used with any of these lenses.
8. Rotate the lens turret (item#10) to select the proper lens for ideal viewing.
9. The greater the magnification the darker the room should be.
HORIZONTAL PROJECTION
1. Follow the above instructions; then holding the neck of the microprojector with
your left hand, place your right hand around the back of the focusing knob(item#9),
and pull the projecting mechanism up into the horizontal position.
2. When using liquids and projecting horizontally, the instrument head must be
placed in a vertical position. Bring the specimen into focus while in the vertical posi-
tion, then move the mirror( item#16) into the light path and adjust so the image
appears on the screen. Select the lens desired and refocus.
your left hand, place your right hand around the back of the focusing knob(item#9),
and pull the projecting mechanism up into the horizontal position.
2. When using liquids and projecting horizontally, the instrument head must be
placed in a vertical position. Bring the specimen into focus while in the vertical posi-
tion, then move the mirror( item#16) into the light path and adjust so the image
appears on the screen. Select the lens desired and refocus.
LIGHT POLARIZATION
1. Rotate the polarizing lens/analyzer (item #5 - darker lens) until the lens is
beneath the light beam.
2. Rotate the Revolving Lens Turret (item #10) until the RED “P” on the edge of
the disk is directly below the RED line.
3. Place a slide containing polarizing material on the stage (item #8).
4. Bring into focus and change colors by turning the polarizing lens (item #14)
beneath the light beam.
2. Rotate the Revolving Lens Turret (item #10) until the RED “P” on the edge of
the disk is directly below the RED line.
3. Place a slide containing polarizing material on the stage (item #8).
4. Bring into focus and change colors by turning the polarizing lens (item #14)
1. Lamp Housing Cap
2. Lamp Housing Cap
Screw
3. Horizontal Positioning
Tension Bolt
2. Lamp Housing Cap
Screw
3. Horizontal Positioning
Tension Bolt
6. Light Diffusing Lens
7. Stage Clips
9. Focusing Knob
13. 6.5mm Lens
4. Lamp Housing
5. Polarizing
Lens/Analyzer
Lens/Analyzer
15. (5x) Widefield
Auxiliary Lens
Auxiliary Lens
8. Stage
11. 16mm Lens
12. 10mm Lens
12. 10mm Lens
10. Revolving Lens
Turret
Turret
16. Mirror