KitchenAid kudd03dtpa Specification Guide
A
B
25"
(63.5 cm)
¹⁄₂
"
(1.3 cm)
8"
(20.3 cm)
Drawer Dishwasher
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
KUDD03DT
KUDH03DT
KUDH03DT
Contact a qualified electrician.
Ensure that the electrical installation is adequate
and in conformance with all national and local
codes and ordinances.
and in conformance with all national and local
codes and ordinances.
You must have:
●
120-volt, 60 Hz, AC-only, 15- or 20- amp fused
electrical supply.
electrical supply.
●
Copper wire only.
We recommend:
●
A time-delay fuse or circuit breaker.
●
A separate circuit.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Instructions packed with product. Specifications subject to change without notice.
Ref. W10300220 Rev A
2-16-10
®
ELECTRICAL REQUIREMENTS
●
Use the new drain hose supplied with your
dishwasher. If this is not long enough, use a new
drain hose with maximum length of 12 ft (3.7 m)
that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and
fits the 1" (2.5 cm) drain connector of the
dishwasher.
dishwasher. If this is not long enough, use a new
drain hose with maximum length of 12 ft (3.7 m)
that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and
fits the 1" (2.5 cm) drain connector of the
dishwasher.
●
Connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is
recommended that the drain hose either be looped
up and securely fastened to the underside of the
counter, or be connected to an air gap.
above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is
recommended that the drain hose either be looped
up and securely fastened to the underside of the
counter, or be connected to an air gap.
●
Use a drain air gap if the drain hose is connected
to house plumbing lower than 20" (50.8 cm)
above the subfloor or floor.
to house plumbing lower than 20" (50.8 cm)
above the subfloor or floor.
●
Use
¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances. Failure to meet codes and
ordinances could lead to fire or electrical shock.
Proper installation is your responsibility.
ordinances could lead to fire or electrical shock.
Proper installation is your responsibility.
●
Contact a qualified installer to ensure that the dishwasher is installed to meet all electrical and
plumbing national and local codes and ordinances.
●
Install the dishwasher as specified in these instructions.
●
Have everything you need to properly install dishwasher.
●
Keep the dishwasher and water lines leading to dishwasher from freezing. Damage from freezing
is not covered by the warranty.
●
This dishwasher is manufactured for indoor use only.
●
Install and level dishwasher on a floor that will hold the weight, and in an area suitable for its
size and use.
WATER SUPPLY REQUIREMENTS
●
A hot water line with 20-120 psi (138-862 kPa)
water pressure.
water pressure.
●
120°F (49°C) water temperature at dishwasher.
●
Flexible braided fill line (
¹⁄₂" minimum plastic
tubing is not recommended).
DRAIN REQUIREMENTS
INSTALLATION CLEARANCES
Cutout dimensions
Preferred utility area
23
³⁄₈
"
(59.5 cm)
19
¹⁄₄
"
(48.9 cm)
1
¹⁄₂
"
(3.75 cm)
24"
(61 cm)
33
³⁄₄"
(85.7 cm)
24"
24"
(61 cm)
33
⁷⁄₈"
(85,7 cm)
(61 cm)