Frigidaire glgq942cs0 Operating Guide

Read your dryer Use and Care Guide.  It has
important safety and warranty information.  It also
has many suggestions for best drying results.

  To reduce the risk of fire, electric

shock or injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS in your dryer Use and
Care Guide before operating this appliance.

Read “Drying Procedures” in your Use and Care
Guide.  It explains these operating steps in detail.

1. Prepare items for drying.

2. Check that lint screen is clean and in place.

3.  Load the dryer. If desired, add a dryer fabric

softener sheet.  Close the door.

4.  Press CYCLES until desired cycle is selected.

Suitable drying temperature, dryness level and
options will automatically be displayed.  To
change these settings, press TEMPS, DRY-
NESS and OPTIONS until the desired selec-
tions are made.  Those adjustments to the cycle
will automatically be remembered each time
that cycle is selected.

5.  To select or delete Press Saver and Air Fluff/

No Heat, press OPTIONS until the flashing light
indicates a desired option.  Then press SE-
LECT to add or delete the option.

6.  If you wish to return to the factory settings, press

and hold “CYCLES” and “OPTIONS” at the
same time for 5 seconds and release.  The dis-
play will show two dashes for a few seconds
indicating that the factory settings have been
selected.

Note:  To provide the best care for your laundry
items, not all temperatures, dryness levels and op-
tions are available with all cycles.

7.

Add desired features by pressing symbols for
·

Control Lock

·

End-of-Cycle Signal

·

Time Dry

8.

Press START to begin cycle.
·

To pause the cycle, press STOP/CANCEL
once.  “PAU” will flash alternately with the
time remaining display. To resume the

cycle, press START again.

·

To stop or clear the cycle, press STOP/

CANCEL twice.

9.

A signal will sound near the end of the cycle
and periodically during Press Saver when the
signal option is selected.  When the cycle ends,
remove items immediately and hang or fold.

10. Clean lint screen after every load.

For best results, follow the fabric care label instruc-
tions on items to be dried.

Auto Dry cycles take the guesswork out of drying time.
The load will automatically be dried at the selected
temperature to the desired dryness level.  The dryer
senses the moisture level of the load as it tumbles
through heated air.  Auto Dry cycles save time and
energy and protect fabrics.

When the load has reached the selected dryness level,
it will continue to tumble, unheated, during a Cool Down
period.  This helps reduce wrinkling and makes items
easier to handle during unloading.

Drying time varies depending on size and dampness of
load and fabric type.  Room temperature and humidity,
type of installation and electrical voltage or gas pres-
sure can also affect drying time.

The following will be displayed during an Auto Dry cycle:
·

The Estimated Drying time for the cycle se-
lected will be displayed for approximately 5
minutes.

·

The “Ad” is displayed until the Estimated Dry-
ing Time for your specific load has been deter-
mined.

·

The cycle status will change from “Auto Dry”
to “Cool Down” while the load is being tumbled
without heat.

·

“dn” is displayed when the cycle is done.

·

If the Press Saver option has been selected, the
load will continue to tumble without heat. The cycle
status will change to “Press Saver” and “dn” will be
displayed.

Select this Auto Dry cycle for cotton items.

Select this Timed Dry cycle to quickly dry a small load
made up of just a few items.  (Auto Dry is not available
with this cycle.)

Select this Auto Dry cycle for towel loads.

Select this Auto Dry cycle for permanent press items.

Select this Auto Dry cycle for knit and delicate items.

Select Touch Up to help remove wrinkles from clean
and dry items that were not taken from the dryer at the
end of the cycle, have been stored in crowded closets
or drawers, or unpacked from luggage following a trip.
It provides approxumately 10 minutes of low heat tum-
bling followed by a 5-minute cool down period.

PN 134306100  (0311)

Page 1