Fujitsu PRIMERGY TX200 S4 VFY:T2004SP021GB Leaflet
Product codes
VFY:T2004SP021GB
Datasheet
Issue: June 16, 2008
PRIMERGY TX200 S4
Page 2 / 2
All rights reserved, including intellectual property rights. Technical data subject to modifications and
delivery subject to availability. Any liability that the data and illustrations are complete, actual or
correct is excluded.
Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which
by third parties for their own purposes may infringe the rights of such owner.
For further information see http://www.fujitsu-siemens.com/terms_of_use.html
Copyright © Fujitsu Siemens Computers 07/2008
delivery subject to availability. Any liability that the data and illustrations are complete, actual or
correct is excluded.
Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which
by third parties for their own purposes may infringe the rights of such owner.
For further information see http://www.fujitsu-siemens.com/terms_of_use.html
Copyright © Fujitsu Siemens Computers 07/2008
Published by
Company stamp
Type
Dual Socket Tower Server
System board D 2509
Chip set
Chip set
Intel® 5000Z
Processors
Dual- or Quad-Core Intel® Xeon® (1 - 2)
Frequencies
(GHz)
(GHz)
E5205 (1.86) 65W DC / L5310 (1.60), L5410 (2.33),
L5420 (2.50) 50W QC / E5405 (2,00), E5420 (2.50)
E5430 (2.66 GHz) 80W QC
L5420 (2.50) 50W QC / E5405 (2,00), E5420 (2.50)
E5430 (2.66 GHz) 80W QC
Front-Side-Bus 1066 (E5205, L5310), 1333 MHz
SLC
SLC
2x4 MB (53xx), 6 MB (E52xx), 2x 6 MB (54xx) ECC
Memory
1 GByte up to max. 24 GByte
2-way interleaved, registered ECC PC2--5300F FullyBuffered DIMM
RAM; 3 banks with 2 slots each for modules 512 MB, 1, 2 and 4 GB;
SDDC (Chipkill) and hot-spare memory opt.
Flash-EPROM
RAM; 3 banks with 2 slots each for modules 512 MB, 1, 2 and 4 GB;
SDDC (Chipkill) and hot-spare memory opt.
Flash-EPROM
Local BIOS update with floppy disk; Remote BIOS-Update via LAN with
Global Flash and service partition
Interfaces
Global Flash and service partition
Interfaces
Serial 1
1x RS-232-C (9-pin) (usable for iRMC or
system or shared)
system or shared)
Serial 2
1x RS-232-C (9-pol)
Parallel (option)
Centronics, 25-pin, EPP/ECP comp.
Keyboard, Mouse
2x PS/2
USB 2.0
1x front, 2x back (UHCI, 480 Mbit/s)
2x internal for backup drive
2x internal for backup drive
Graphics
1x VGA (15-pin)
LAN
1x RJ45, 1x Service-LAN 10/100 (can be
switched on Gbit port)
switched on Gbit port)
Front Panel
On/off switch; NMI-, reset button; LEDs for global error (amber/ yellow
for Health and CSS), identification (blue), hard disks access (green),
power (amber/green); (back: global error, identification, LAN activity,
LAN mode)
for Health and CSS), identification (blue), hard disks access (green),
power (amber/green); (back: global error, identification, LAN activity,
LAN mode)
Onboard or integrated controller**
IDE (ATA100)
IDE (ATA100)
1-channel Fast-IDE controller for 1 device
SATA configuration
(6311ESB)
(6311ESB)
4-port SATA for internal HDD`s with RAID 0,
1, 10 for Windows and Linux, RAID 5 iButton
key optional) plus 2x for accessible drives
1, 10 for Windows and Linux, RAID 5 iButton
key optional) plus 2x for accessible drives
SAS configuration
in PCIe slot either
LSI 1068
or LSI 1078
in PCIe slot either
LSI 1068
or LSI 1078
8 port SAS for internal HDD´s and internal
backup devices with
RAID 0, 1 (Integrated Mirroring Enhanced
also for odd numbered HD´s for Windows and
Linux)
with RAID 0, 1, 10, 5, 50, 6, 60 (256 or 512
MB RAID Cache and opt. BBU)
backup devices with
RAID 0, 1 (Integrated Mirroring Enhanced
also for odd numbered HD´s for Windows and
Linux)
with RAID 0, 1, 10, 5, 50, 6, 60 (256 or 512
MB RAID Cache and opt. BBU)
LAN (BCom 5708)
1x 10/100/1000 Mbit/s Ethernet
(TCP/IP acceleration)(PXE-Boot via LAN from
PXE server), iSCSI Boot (also diskless) via
onboard LAN
(TCP/IP acceleration)(PXE-Boot via LAN from
PXE server), iSCSI Boot (also diskless) via
onboard LAN
Server management
Integrated Remote Management Controller
(iRMC S2, 32 MB attached memory) incl.
graphics controller, IPMI 2.0
(iRMC S2, 32 MB attached memory) incl.
graphics controller, IPMI 2.0
Hard disk drives
73, 146, 300 Gbyte 3.5-inch SAS or 36, 73,
146 Gbyte 2.5-inch SAS or 160, 250, 500,
750 Gbyte 3.5-inch SATA
3.5-inch SAS / SATA mix only in separate
HD-cages and in separate RAID sets, no later
conversion from 3,5 to 2,5-inch possible
146 Gbyte 2.5-inch SAS or 160, 250, 500,
750 Gbyte 3.5-inch SATA
3.5-inch SAS / SATA mix only in separate
HD-cages and in separate RAID sets, no later
conversion from 3,5 to 2,5-inch possible
1 Gbyte equals one billion bytes when referring to hard disk drive capacity; accessible capacity
may vary.
may vary.
I/O Slots (Standard)
4x PCIe x8 (x4 wired), 2x long, (1x for modular SAS RAID controller),
(2 slots x8 with performance adapter)
2x PCI-X 64-bit/ 100 MHz, long, 3,3V; (1x with max. 133 MHz
(IOOP™), if only 1 Slot is occupied)
1x PCI 32-bit / 33 MHz, 5V
Drive bays
(2 slots x8 with performance adapter)
2x PCI-X 64-bit/ 100 MHz, long, 3,3V; (1x with max. 133 MHz
(IOOP™), if only 1 Slot is occupied)
1x PCI 32-bit / 33 MHz, 5V
Drive bays
for hard disks
4x 3.5-inch, for Hot-plug SAS/SATA or
4 or 8x 2.5-inch for Hot-plug SAS
4 or 8x 2.5-inch for Hot-plug SAS
for optional hard
disks
disks
2x 3.5/1-inch HDD box only in SAS configuration
or
8x 2.5-inch for SAS (occupy 2x 5.25/1.6-inch bay)
or
8x 2.5-inch for SAS (occupy 2x 5.25/1.6-inch bay)
for accessible
drives
drives
3x 5.25/1.6-inch, (all possible options described in
relevant system configurator)
1x 3,5/1-inch, for FDD (optional)
relevant system configurator)
1x 3,5/1-inch, for FDD (optional)
System fans
Standard 3 fans, redundant (option): 3 + 1 fans
Electrical values ***
Electrical values ***
1x standard or 2x optional redundant hot-plug power supplies
Output power
Output power
635W (std) / 700 W / 1 + 1 x 700 W each
Rated voltage range
100 – 127 V / 200 - 240 V
Rated frequency
50 - 60 Hz
Max. rated current
100 – 127 V / 200 - 240 V 9.0 A / 4.5 A
Rated current in basic
configuration
configuration
100 – 127 V / 200 - 240 V 2.0 A / 0.86 A
Active power
512 W
Apparent power
531 VA
Heat emission
1843 kJ/h (1746 btu/h)
Temperature/Noise/Dimensions/Weight
Ambient temperature
Ambient temperature
10°C - 35°C (DIN IEC 721-3-3) class 3K2
ETSI 300 019-2-3 Class 3.1
ETSI 300 019-2-3 Class 3.1
Declared noise emission
according to ISO 9296
according to ISO 9296
idle* operating* *(ISO 7779)
ETSI 300 753 Class 3.1
ETSI 300 753 Class 3.1
L
WAd
(1 B = 10 dB) :
5.3 B*** 5.4 B***
L
pAm
(bystander position): 35 dB*** 37 dB***
Floor-stand (HxWxD)mm 447 x 215 (372 with tilt protection) x 699
Rack (HxWxD)
Rack (HxWxD)
215 x 486 x 777 mm;
Rack mounting depth 742 mm; 5U
Rack mounting depth 742 mm; 5U
Weight
35 kg (configuration dependent)
Compliance with Norms and Standards
Product safety
Product safety
Global
IEC 60950-1
Europe
EN 60950-1
USA
UL 60950-1
Canada
CAN/CSA C22.2 No. 60950-1-03
Electromagnetic compatibility
This product and the released accessories, are in compliance with
emission class A. In certain cases measures have to be taken to
reduce the electro magnetic influence to other equipment.
Europe
This product and the released accessories, are in compliance with
emission class A. In certain cases measures have to be taken to
reduce the electro magnetic influence to other equipment.
Europe
EN 55022 class A, EN 55024,
EN 61000-3-2 / 3-3, ETSI EN300386
EN 61000-3-2 / 3-3, ETSI EN300386
Taiwan / Japan
CNS 13438 class A; VCCI class A
Australia / New Zealand
AS / NZS CISPR 22 class A
USA / Canada
FCC class A
Declaration of conformity
Europe (CE)
Europe (CE)
2004/108/EC(EMC);2006/95 EC(LVD)
North America
FCC class A
Approvals
Product safety
Global
CB
Europe
CE
USA / Canada
CSA
US
/ CSA
C
There is general compliance with the safety requirements of all
European countries and North America. National approvals required
in order to satisfy statutory regulations or for other reasons, can be
applied for on request.
European countries and North America. National approvals required
in order to satisfy statutory regulations or for other reasons, can be
applied for on request.
Supported server operating systems
See actual release status
See actual release status
operating systems
: e.g. Windows Server
2003; Windows Server 2008, Novell SUSE Linux Enterprise Server ,
Red Hat Enterprise Linux; VMware ESX (Support of Debian, Ubuntu,
Mandriva Linux and other Linux derivatives
Red Hat Enterprise Linux; VMware ESX (Support of Debian, Ubuntu,
Mandriva Linux and other Linux derivatives
on demand
)
** For supported controllers (onboard and PCI cards for SAS, SATA,
RAID, LAN, WAN, etc.), please refer to the corresponding system
configurator.
*** only with standard fans and standard PSU
Server Management (see separate data sheets)
Standard:
RAID, LAN, WAN, etc.), please refer to the corresponding system
configurator.
*** only with standard fans and standard PSU
Server Management (see separate data sheets)
Standard:
PRIMERGY ServerView Suite; PDA, ASR&R
Optional: (excerpt)
iRMC S2 Advanced Pack, ServerView Local
Service Panel (LSP)
Service Panel (LSP)