Revel c32 Installation Instruction
Performa Pedestal 32/50a
Assembly Instructions
Step 1: Locate the parts bag (included with the stand) that
contains spikes, screws, lock nuts, Allen wrench and hole
plug. Set all parts aside.
plug. Set all parts aside.
Step 2: Begin the stand assembly by fastening the three tubes
to the top plate with three enclosed 6mm x 18mm Phillips
flat head screws. Start all screws by hand before tightening
with a screwdriver.
flat head screws. Start all screws by hand before tightening
with a screwdriver.
Step 3: Place the stand upside-down and attach the bottom
base with three 8mm x 20mm hex cap screws using the
Allen wrench (included).
Allen wrench (included).
Step 4: With the stand upside-down as shown at the top of the
next column, install the spikes (from Step 1) to the bottom
of the base. Thread spikes about halfway and then use a
wrench or pliers to tighten the locking nut. Tighten all
screws again after stand is assembled. Turn stand upright and
adjust spikes if required.
of the base. Thread spikes about halfway and then use a
wrench or pliers to tighten the locking nut. Tighten all
screws again after stand is assembled. Turn stand upright and
adjust spikes if required.
Step 5: Place the Loudspeaker* as shown onto a carpeted surface
or a soft towel. Attach the assembled stand with four 8-32 x
3/4 Phillips flat head screws.
3/4 Phillips flat head screws.
(3) 6mm x 18mm flat
head screws
head screws
(4) 8-32 x 3/4” flat head screws
(Start All Screws By Hand Before
Tightening with Screwdriver)
Tightening with Screwdriver)
Revel Performa
Pedestal 32
(Assembled)
Top Plate
B o t t o m
Base
Base
(3) 8mm x 20mm hex cap screws
Top View of Top
Plate
Plate
(1) Large Tube
(2) Smaller Tubes
Top Wire Access Hole
Loudspeaker*
Bottom
Base
Base
Nut
Spike
Bottom Wire Access Hole
Thread the end of the speaker wire
into the pedestal through the top
wire access hole at the rear of the
large tube and back out through
the hole in the bottom base.
into the pedestal through the top
wire access hole at the rear of the
large tube and back out through
the hole in the bottom base.
Fasten angled end
of tubes to the Top
Plate.
of tubes to the Top
Plate.
There are different size threads on each end of the tube(s).
Make sure that the end attached to the top plate properly fits
the 6mm x 18mm screws before attempting to tighten. It is not
possible to attach the wrong end to the top plate as the threads
will not fit the 8mm x 20mm screws which are used to attach
to the bottom base.
Make sure that the end attached to the top plate properly fits
the 6mm x 18mm screws before attempting to tighten. It is not
possible to attach the wrong end to the top plate as the threads
will not fit the 8mm x 20mm screws which are used to attach
to the bottom base.
(Rear)
Top Wire Access Hole
* The Performa Pedestal 32/50a is designed to support either
the Revel Performa C32 Loudspeaker or the Revel Performa
C50a Loudspeaker.
the Revel Performa C32 Loudspeaker or the Revel Performa
C50a Loudspeaker.
3 Oak Park Drive, Bedford, MA USA 01730-0413 | Tel: 781-280-0300 | Fax: 781-280-0490 | www.revelspeakers.com | 12/03 | Part No. 352289-001