ONKYO TX-SR502 Instruction Manual
3
Precautions
1. Recording Copyright
—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
out the permission of the copyright holder.
2. AC Fuse
—The AC fuse inside the TX-SR502/
TX-SR502E is not user-serviceable. If you cannot
turn on the TX-SR502/TX-SR502E, contact your
Onkyo dealer.
turn on the TX-SR502/TX-SR502E, contact your
Onkyo dealer.
3. Care
—Occasionally you should dust the
TX-SR502/TX-SR502E all over with a soft cloth.
For stubborn stains, use a soft cloth dampened with
a weak solution of mild detergent and water. Dry the
TX-SR502/TX-SR502E immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
For stubborn stains, use a soft cloth dampened with
a weak solution of mild detergent and water. Dry the
TX-SR502/TX-SR502E immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the TX-SR502/
TX-SR502E’s rear panel (e.g., AC 230 V, 50 Hz or
AC 120 V, 60 Hz).
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the TX-SR502/
TX-SR502E’s rear panel (e.g., AC 230 V, 50 Hz or
AC 120 V, 60 Hz).
The Worldwide model has a voltage selector for
compatibility with power systems around the world.
Before you plug in this model, make sure that the
voltage selector is set to the correct voltage for your
area.
compatibility with power systems around the world.
Before you plug in this model, make sure that the
voltage selector is set to the correct voltage for your
area.
For American model
Setting the [STANDBY/ON] switch to STANDBY
does not fully shutdown the TX-SR502. If you do
not intend to use the TX-SR502 for an extended
period, remove the power cord from the AC outlet.
does not fully shutdown the TX-SR502. If you do
not intend to use the TX-SR502 for an extended
period, remove the power cord from the AC outlet.
Memory backup
The TX-SR502/TX-SR502E uses a battery-less mem-
ory backup system in order to retain radio presets and
other settings when it’s unplugged or in the case of a
power failure. Although no batteries are required, the
TX-SR502/TX-SR502E must be plugged into an AC
outlet in order to charge the backup system.
(On non-American models, the TX-SR502/
TX-SR502E’s POWER switch must be set to ON in
order to charge the backup system.) Once it has been
charged, the TX-SR502/TX-SR502E will retain the set-
tings for several weeks, although this depends on the
environment and will be shorter in humid climates.
ory backup system in order to retain radio presets and
other settings when it’s unplugged or in the case of a
power failure. Although no batteries are required, the
TX-SR502/TX-SR502E must be plugged into an AC
outlet in order to charge the backup system.
(On non-American models, the TX-SR502/
TX-SR502E’s POWER switch must be set to ON in
order to charge the backup system.) Once it has been
charged, the TX-SR502/TX-SR502E will retain the set-
tings for several weeks, although this depends on the
environment and will be shorter in humid climates.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
with the following code:
Blue: Neutral
Brown: Live
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse
need to be replaced, please ensure that the replacement
fuse has a rating of 5 amperes and that it is approved by
ASTA or BSI to BS1362. Check for the ASTA mark or
the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMPERE SOCKET.
If in any doubt, consult a qualified electrician.
need to be replaced, please ensure that the replacement
fuse has a rating of 5 amperes and that it is approved by
ASTA or BSI to BS1362. Check for the ASTA mark or
the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMPERE SOCKET.
If in any doubt, consult a qualified electrician.
For European Models
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
I. MORI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
TX-SR502_En.book Page 3 Tuesday, February 17, 2004 12:14 PM