Philips 40PFL4706 40PFL4706/F7 User Manual
Product codes
40PFL4706/F7
11
English
You must set [Home]. Otherwise, personalized picture and sound
settings will not be memorized after the unit goes to standby mode.
•
settings will not be memorized after the unit goes to standby mode.
•
Select [Retail store], the unit will be set up with predefi ned setting
for retail displays. In this setting, the power consumption may
possibly exceed the limited requirement of the ENERGY STAR
®
R
R
qualifi cation.
•
Select [Home], the unit will be set to maximize energy effi ciency.
Picture and sound settings can be adjusted and saved as per your
personal preferences.
Press
Í/Æ to select [Start], then press OK to begin [Settings assistant].
Settings assistant will allow you to customize your picture settings to
your personal preference. You will see a series of test pictures where
the right side and left side differ. Select the side that is most pleasing to
you with the Left/Right buttons.
Cancel
Start
Select [Picture A] or [Picture B] by pressing
Í /Æ that is the most
pleasing to you, then press OK. You see 5 different pictures to be
completed.
completed.
Cancel
Picture A
Picture B
Which side of the picture do you prefer?
Press
Í /Æ to select [Store], then press OK.
Cancel
Store
Store your preferences.
Press OK to fi nish [ Settings assistant].
Exit
The TV has learned your preferences.
Press
Í /Æ to select [Finish], then press OK.
Finish the Setup.
Note
•
If you are not receiving a signal from your cable service, contact the CATV provider.
•
If you press
. during autoprogram, an installation will be canceled except the
language selection.
•
The initial autoprogram function can be executed for either [Antenna] or [Cable]
only once. When you change the connection (Antenna / Cable), set autoprogram again.
(Refer to page 35.)
only once. When you change the connection (Antenna / Cable), set autoprogram again.
(Refer to page 35.)
Switching on and initial setup
Before you switch on the TV, check that the AC power cord is properly
connected. Press
connected. Press
.POWER at the right side of the TV, or press
.(standby-On) on the remote control. The TV normally takes 25-30
seconds to start up and the following screen appears the fi rst time you
turn on the TV.
turn on the TV.
After you read a welcome screen, follow the on-screen instructions
to select your language and complete your TV setup. Installation takes
approximately 20 minutes.
to select your language and complete your TV setup. Installation takes
approximately 20 minutes.
Select your menu
language with the
Up/Down buttons on
your remote control,
press the OK button to
proceed.
language with the
Up/Down buttons on
your remote control,
press the OK button to
proceed.
●
●
●
English
Français
Español
●
En
En
En
En
gl
gl
gl
gl
gl
g
g
g
g
g
is
is
is
is
s
h
h
h
h
Network setup screen will appear. Use
Î/ï/Í/Æ to select [Next] >
[Wireless] / [Wired], then press OK.
•
•
If you select [Wireless], use
Î/ï to select a setting and then press
OK.
Setting items
Description
Easy connect
Select this setting if your router has a Wi-Fi
Protected Setup (WPS) button. Start scanning
for wireless networks on the TV after pressing
the WPS button on your router. If connection
test fails, refer to the router's manual for more
details.
Scan
Search for wireless networks automatically
and select the wireless network name (SSID)
from the list. see ‘Wireless network setting
(Auto)’on page 30.
•
If you select [Wired], use
Î/ï to select a setting and then press
OK.
Connection test will start automatically. (See ‘Connection test’ on page 30.)
Press
Press
Î/ï to select the desired mode for energy saving, then press OK.
Retail store
Home
"Home" is recommended for
normal home use.In the Retail
Store mode all settings are
fixed.
normal home use.In the Retail
Store mode all settings are
fixed.
Select [Retail store] if you want backlight to be brighter.
Select [Home] to reduce power consumption.
Select [Home] to reduce power consumption.
EN