Bunn OL User Guide
Page 16
CA
UT
ION
DIS
CA
RD
DE
CA
NT
ER
IF:
. C
RA
CK
ED
. S
CR
AT
CH
ED
. B
OIL
ED
DR
Y
. H
EA
TE
D W
HE
N E
MP
TY
. U
SE
D O
N H
IGH
FL
AM
E
. O
R E
XP
OS
ED
EL
EC
TR
IC
E
LE
ME
NT
S
FA
ILU
RE
TO
CO
MP
LY
RI
SK
S I
NJ
UR
Y
PN
: 6
58
19
85
BU
NN
-O
-M
AT
IC
CO
RP
OR
AT
ION
FU
NN
EL
CO
NT
EN
TS
AR
E H
OT
!
FIG. 9 WARMER SWITCHES
FIG. 10 WARMER SWITCHES
FIG. 11 WARMER SWITCH WIRING
SERVICE (cont.)
Warmer Switch(es)
OL:
On/Off Brew Station & Upper
RL:
On/Off Brew Station
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the Wir-
ing Diagrams and check the brewer wiring harness.
If voltage is not present as described, refer to the Wir-
ing Diagrams and check the brewer wiring harness.
4.
Check the voltage across the other switch termi-
nal and the terminal on the indicator lamp with
white or red wires with a voltmeter when the
switch is in the upper position. Connect the
brewer to the power source. The indication must
be as described in step 2. Voltage must not be
present across these terminals in the lower posi-
tion.
nal and the terminal on the indicator lamp with
white or red wires with a voltmeter when the
switch is in the upper position. Connect the
brewer to the power source. The indication must
be as described in step 2. Voltage must not be
present across these terminals in the lower posi-
tion.
5.
Disconnect the brewer from the power source.
If voltage is present as described the switch is oper-
ating properly.
If voltage is not present as described, replace the
switch.
ating properly.
If voltage is not present as described, replace the
switch.
Removal and Replacement:
1.
1.
Compress the clips inside the housing and gen-
tly push the switch through the opening.
tly push the switch through the opening.
2.
Remove the wires from the switch terminals.
3.
Refer to FIG. 11 when reconnecting the wires.
4.
Push the new switch firmly into the opening.
Location:
These switches are located beneath and to the
left of their associated warmers as viewed from the
front, FIG.s 9 and 10.
front, FIG.s 9 and 10.
Test Procedure:
1.
1.
Locate the switch terminal with black wires that
do not go to the nearby indicator lamp.
do not go to the nearby indicator lamp.
2.
Check the voltage across this terminal and the
terminal on the indicator lamp with white or red
wires with a voltmeter. Connect the brewer to
the power source. The indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 or 240 volts ac for two wire 200 volt or
240 volt models.
c) 100 volts ac for two wire 100 volt models.
terminal on the indicator lamp with white or red
wires with a voltmeter. Connect the brewer to
the power source. The indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 or 240 volts ac for two wire 200 volt or
240 volt models.
c) 100 volts ac for two wire 100 volt models.
3.
Disconnect the brewer from the power source.
MODEL
OL Upper
OL Upper
BLK A
to Warmer
to Indicator Lamp
to Indicator Lamp
BLK B
to Harness P3
OL On/Off Brew Station
BLK A
to Indicator Lamp
to Brew Station Warmer
to Level Switch
to Brew Station Warmer
to Level Switch
BLK B
to Terminal Block
RL On/Off Brew Station
BLK A
to Indicator Lamp
to Level Switch
to Brew Station Warmer
to Level Switch
to Brew Station Warmer
BLK B
to Left Front Warmer Switch
to Right Front Warmer Switch
to Right Front Warmer Switch
BLK (A) (see below)
BLK (B) (see below)
P1712
P1713
P1697
WA
RN
IN
G
!
HI
GH
H
EA
T W
AR
ME
R
DO
N
OT
B
OI
L D
EC
AN
TE
R
DR
Y
KE
EP
C
OM
BU
ST
IB
LE
S
AW
AY
FA
ILU
RE
TO
C
OM
PL
Y
RI
SK
S
GL
AS
S
FA
ILU
RE
/H
OT
LI
QU
ID
BU
RN
S
AN
D
FIR
E
HA
ZA
RD
CA
UT
ION
DIS
CA
RD
DE
CA
NT
ER
IF:
. C
RA
CK
ED
. S
CR
AT
CH
ED
. B
OIL
ED
DR
Y
. H
EA
TE
D W
HE
N E
MP
TY
. U
SE
D O
N H
IGH
FL
AM
E
. O
R E
XP
OS
ED
EL
EC
TR
IC
E
LE
ME
NT
S
FA
ILU
RE
TO
CO
MP
LY
RI
SK
S I
NJ
UR
Y
PN
: 6
58
19
85
BU
NN
-O
-M
AT
IC C
OR
PO
RA
TIO
N
FU
NN
EL
CO
NT
EN
TS
AR
E H
OT
!
10020 111598