Bunn single multi-brewwise dbc Operating Guide
Page 26
PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)
Setting Pulse Brew - BY EXAMPLE:
1. This display should read CONTAINER READY?
1. This display should read CONTAINER READY?
Place a container under the sprayhead. Place a
brew funnel containing a filter and grounds on top
of the GPR server so that the spray and coffee
bed can be viewed.
brew funnel containing a filter and grounds on top
of the GPR server so that the spray and coffee
bed can be viewed.
2. Choose the batch size to be set by pressing the
pad next to the indicator light on the left brew side.
The batch size indicator selected will be flashing.
The batch size indicator selected will be flashing.
3. If everything is in place, press YES in the CON-
TAINER READY? screen. The display should read
PRESS BREW TO START 1ST ON TIME.(a)
PRESS BREW TO START 1ST ON TIME.(a)
4. Press and release the "BREW" pad. The brew wa-
ter will start to flow into the funnel and the water
level will rise.(b)
level will rise.(b)
5. Watch the flow of water. When it reaches the de-
sired level in the funnel, press and release the
"BREW" pad again to end the 1ST ON TIME.(c)
"BREW" pad again to end the 1ST ON TIME.(c)
6. The spray will stop and the brew funnel will start
to empty. When the water level in the funnel drains
to the desired level, press "BREW" again to end
the OFF-TIME. This also begins the spray of wa-
ter for the final setting.(d)
to the desired level, press "BREW" again to end
the OFF-TIME. This also begins the spray of wa-
ter for the final setting.(d)
7. The brew water will begin again and the water level
in the funnel will rise. Watch the flow of water.
When it reaches the desired level, press "BREW"
to end the LAST ON TIME.(e)
When it reaches the desired level, press "BREW"
to end the LAST ON TIME.(e)
8. The display should now show the 1st, off and last
times for the batch size just programmed. After a
5 second delay, the display will read BATCHES
DONE? (f and g)
5 second delay, the display will read BATCHES
DONE? (f and g)
9. If other batches need to be modified, press NO.
The display will go back to SET BY EXAMPLE.
Press YES, then press a different batch size pad
and repeat steps 1 through 8. Repeat until all the
desired batch sizes are set for the left side. (g)
Press YES, then press a different batch size pad
and repeat steps 1 through 8. Repeat until all the
desired batch sizes are set for the left side. (g)
10. When finished press YES in BATCHES DONE?. The
display will then read SET PREINFUSION. Another
alternative is to press the "ON/OFF/LOWER" pad
located on the front panel of the brewer to exit
SET PULSE BREW and return to the MAIN
SCREEN.
alternative is to press the "ON/OFF/LOWER" pad
located on the front panel of the brewer to exit
SET PULSE BREW and return to the MAIN
SCREEN.
NOTE: Pressing ® before reaching the final setting
screen exits the setup and retains the old values.
screen exits the setup and retains the old values.
SET BY EXAMPLE
RETURN TO
SET BY EXAMPLE
SEE MODIFYING
PREINFUSION
5 SEC. DELAY
CONTAINER RDY?
QUIT YES
QUIT YES
PRESS BREW TO
SET 1ST ON TIME
PRESS BREW TO
END 1ST ON TIME
PRESS BREW TO
END OFF TIME
PRESS BREW TO
END LAST ON TIME
1ST OFF LAST
X:XX X:XX X:XX
X:XX X:XX X:XX
SET PREINFUSION?
NO YES
BATCHES DONE?
NO YES
P3217
37467 110904