SpeakerCraft mt6 one User Guide
3. Slide the ends of the two mounting bars at the tweeter end of the speaker behind the drywall so
the drywall is now between the mounting bars and the back of the speaker baffle. This should be
enough room for the other ends of the mounting bars to clear the other end of the drywall hole
and slide behind the drywall as well. (See Diagram 5)
enough room for the other ends of the mounting bars to clear the other end of the drywall hole
and slide behind the drywall as well. (See Diagram 5)
4. Position the speaker into the hole and start tightening the six screws evenly. This will cause the
mounting bars to properly sandwich the drywall between the self-adjusting mounting bar feet and
the speaker flange. Make sure the speaker is positioned correctly before final tightening of the six
mounting screws. Note: The flange of the speaker is designed to flex and conform to any small
imperfections in the wall’s surface. The tension on the screws should not be tightened so that the
flange bows out. If this occurs, back off the tension on the screws until the bowing is eliminated.
the speaker flange. Make sure the speaker is positioned correctly before final tightening of the six
mounting screws. Note: The flange of the speaker is designed to flex and conform to any small
imperfections in the wall’s surface. The tension on the screws should not be tightened so that the
flange bows out. If this occurs, back off the tension on the screws until the bowing is eliminated.
5. Adjust the pivoting tweeter to the desired position.
6. Adjust the BASS (MT6 THREE & FOUR) and TREBLE (MT6 TWO, THREE & FOUR) switches to the
desired position.
7. Push the grille firmly into the slot in the speaker baffle.
PAINTING THE SPEAKERS
If you plan to paint your speakers, we recommend that it be done prior to installation. If you decide to paint your speakers sometime in
the future, it is best to remove them by simply reversing the steps for Speaker Installation listed above. When painting the speakers, the
paint masks provided in the carton must be installed in place of the grille. The grilles can also be painted, however, great care should be
taken not to clog the holes as this will greatly reduce the sound quality of the speakers. SpeakerCraft recommends only light spray paint-
ing using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are attached to the speaker. If it is necessary to paint
the material under grille, follow the same procedure used to paint the grilles.
the future, it is best to remove them by simply reversing the steps for Speaker Installation listed above. When painting the speakers, the
paint masks provided in the carton must be installed in place of the grille. The grilles can also be painted, however, great care should be
taken not to clog the holes as this will greatly reduce the sound quality of the speakers. SpeakerCraft recommends only light spray paint-
ing using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are attached to the speaker. If it is necessary to paint
the material under grille, follow the same procedure used to paint the grilles.
SPECIAL FIRE WALL INSTALLATION
If you plan to mount your speakers in a fire-rated wall, you should purchase SpeakerCraft 6” Rectangle Sound Enclosures, model #SE1612.
This metal enclosure mounts easily between studs, and contains a standard electrical connector for connecting your speaker cable directly
to the speaker.
This metal enclosure mounts easily between studs, and contains a standard electrical connector for connecting your speaker cable directly
to the speaker.
4. Cutting the hole. CAUTION: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the desired mounting area,
you should start by cutting a small hole in the center of your penciled mounting hole
with a drywall saw. Cut at a 45º angle towards the inside of the hole (See Diagram 2).
Cutting the small hole at this angle will make drywall repair much easier as the piece cut
out can be installed neatly back into the hole. Once you have determined there aren’t
any obstructions in your desired mounting location, start cutting the finished hole at a
90º angle to the wall surface.
you should start by cutting a small hole in the center of your penciled mounting hole
with a drywall saw. Cut at a 45º angle towards the inside of the hole (See Diagram 2).
Cutting the small hole at this angle will make drywall repair much easier as the piece cut
out can be installed neatly back into the hole. Once you have determined there aren’t
any obstructions in your desired mounting location, start cutting the finished hole at a
90º angle to the wall surface.
5. Add insulation. If the area in the wall is not already insulated, add an adequate amount of
insulation material to fill the wall cavity. If the insulation material used is faced with foil or
paper, position the foil or paper away from the speaker.
paper, position the foil or paper away from the speaker.
SPEAKER ADJUSTMENTS
The Mirror Image Technology Series speakers come from the factory with the tweeter facing straight out
from the baffle. This will result in the overall smoothest response. However, depending on your particu-
lar primary area, room acoustics, ceiling height, or personal preference, you may find the sound more
pleasing by pointing the tweeters in a particular direction. If additional treble is desired in the primary
listening area, point the tweeter towards that area; and if less treble is required, point the tweeter away.
When used in a home theater surround sound environment as side or rear channel speakers, the best
result will be obtained by pointing the tweeters toward an adjacent wall. Push gently at the edge of
the tweeter to point it in the desired direction. (See Diagram 3)
CAUTION: Avoid touching tweeter dome as damage WILL occur on metal dome tweeters
(MT6 THREE & FOUR).
from the baffle. This will result in the overall smoothest response. However, depending on your particu-
lar primary area, room acoustics, ceiling height, or personal preference, you may find the sound more
pleasing by pointing the tweeters in a particular direction. If additional treble is desired in the primary
listening area, point the tweeter towards that area; and if less treble is required, point the tweeter away.
When used in a home theater surround sound environment as side or rear channel speakers, the best
result will be obtained by pointing the tweeters toward an adjacent wall. Push gently at the edge of
the tweeter to point it in the desired direction. (See Diagram 3)
CAUTION: Avoid touching tweeter dome as damage WILL occur on metal dome tweeters
(MT6 THREE & FOUR).
Tweeter Adjustment (MT6 TWO, THREE & FOUR):
The 3 vertical buttons with the center button labeled “T” allow for 6dB of TREBLE adjustment. Your
speakers were shipped with the treble set to neutral. This setting provides the most linear frequency
response. If you desire more treble, push the button with the up arrow and the treble will play 3dB
higher. If you want less treble, push the button with the down arrow and the tweeter will play 3dB
lower. To return to the neutral setting, push the “T” button. (See Diagram 4)
The 3 vertical buttons with the center button labeled “T” allow for 6dB of TREBLE adjustment. Your
speakers were shipped with the treble set to neutral. This setting provides the most linear frequency
response. If you desire more treble, push the button with the up arrow and the treble will play 3dB
higher. If you want less treble, push the button with the down arrow and the tweeter will play 3dB
lower. To return to the neutral setting, push the “T” button. (See Diagram 4)
Woofer Adjustment (MT6 THREE & FOUR):
The 3 vertical buttons with the center button labeled “B” allow for 6dB of BASS adjustment. Your
speakers were shipped with the bass set to neutral, resulting in 6
The 3 vertical buttons with the center button labeled “B” allow for 6dB of BASS adjustment. Your
speakers were shipped with the bass set to neutral, resulting in 6
ohm
of impedance. This setting pro-
vides the flattest bass frequency response. If you desire more bass, push the button with the up arrow
and the bass will play 3dB higher and lower the impedance to 4
and the bass will play 3dB higher and lower the impedance to 4
ohm
. If you want less bass, push the
button with the down arrow and the bass will play 3dB lower and increase the impedance to 8
ohm
.
This setting provides a more linear bass frequency response. To return to the neutral setting, push the
“B“ button. (See Diagram 4) Remember that altering the impedance affects the number of speak-
ers able to be driven by an amplifier. If multiple pairs of speakers are to be driven by one amplifier,
SpeakerCraft suggests using the lowest output position (the down arrow) until it is determined that
the amplifier will operate properly with the speakers switched to a higher output mode. If you want to
safely operate multiple pairs of speakers, consider purchasing SpeakerCraft S4 or S8 Speaker Selectors.
“B“ button. (See Diagram 4) Remember that altering the impedance affects the number of speak-
ers able to be driven by an amplifier. If multiple pairs of speakers are to be driven by one amplifier,
SpeakerCraft suggests using the lowest output position (the down arrow) until it is determined that
the amplifier will operate properly with the speakers switched to a higher output mode. If you want to
safely operate multiple pairs of speakers, consider purchasing SpeakerCraft S4 or S8 Speaker Selectors.
SPEAKER INSTALLATION
Note: Your MT6 Series speakers may have come with the optional Jawz
™
speaker wire connector. Before using Jawz
™
, please follow the
instructions included with the connector.
The unique integral mounting bar system incorporated into your MT6 Series speaker allows for a quick installation by following the easy
steps below:
steps below:
1. Remove the grille by pushing the two mounting bars, located at the rear of the speaker, towards the front of the speaker. The long
screws attached to the mounting bars will force the grille off the baffle.
2. Attach the speaker cable, observing the proper polarity with your amplifier ( + to + and - to -). Make sure the left channel of the amplifier
is connected to the left speaker, and
the right channel is connected to the right speaker.
Page 2
MT6 Series Owner’s Manual
MT6 Series Owner’s Manual
Page 3
Diagram 2:
Wall Cut Out
Diagram 3:
Tweeter
Diagram 5:
Mounting Bars
Push Tweeter Here
Diagram 4:
Bass & Treble Adjustment Switches
LIMITED LIFETIME WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and
workmanship, provided the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom
they were purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments
will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case,
the risk or loss or damage in transit is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized
Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period, SpeakerCraft or
the SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below.
If this model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option, may replace the unit with a cur-
rent model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be
required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced
parts and product become the property of SpeakerCraft Inc. Products replaced or repaired under this Warranty will be returned to the
original retail purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate pack-
ing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification
of the product which has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration
caused by environmental conditions. This Warranty will be void if the Serial Number on the product has been removed, tampered with or
defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above,
the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental
or consequential damages arising out of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized
Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or
limitation of consequential damages, so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on the
length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.