SpeakerCraft css6 one User Guide
Page 2
CSS6 Series Owner’s Manual
CSS6 Series Owner’s Manual
Page 3
4. Cutting the hole. CAUTION:This is the most important part of the entire
installation. If you are uncertain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in the center
of your penciled mounting hole with a drywall saw, cutting at a 45º angle
towards the inside of the hole. (See Diagram 2) Cutting the small hole at this
angle will make drywall repair much easier, using the piece cut out. Once you
have determined that there aren’t any obstructions in your desired mounting
location, start cutting the finished hole at a 90º angle to the ceiling surface.
desired mounting area, you should start by cutting a small hole in the center
of your penciled mounting hole with a drywall saw, cutting at a 45º angle
towards the inside of the hole. (See Diagram 2) Cutting the small hole at this
angle will make drywall repair much easier, using the piece cut out. Once you
have determined that there aren’t any obstructions in your desired mounting
location, start cutting the finished hole at a 90º angle to the ceiling surface.
5. Add insulation. If the area in the ceiling is not already insulated, add an
adequate amount insulation material to loosely cover the back of the speaker.
If the insulation material used is faced with foil or paper, position the foil or
paper away from the speaker.
If the insulation material used is faced with foil or paper, position the foil or
paper away from the speaker.
SPEAKER ADJUSTMENTS
Your CSS6 Series speakers come from the factory with the tweeter facing straight
out from the baffle. This will result in the overall smoothest response. However,
depending on your particular primary area, room acoustics, ceiling height, or
personal preference, you may find the sound more pleasing by pointing the
tweeters in a particular direction. If additional treble is desired in the primary
listening area, point the tweeter towards that area; and if less treble is required,
point the tweeter away. Push gently at the edge of the tweeter to point it in the
desired direction. (See Diagram 3) CAUTION: Avoid touching tweeter dome as
out from the baffle. This will result in the overall smoothest response. However,
depending on your particular primary area, room acoustics, ceiling height, or
personal preference, you may find the sound more pleasing by pointing the
tweeters in a particular direction. If additional treble is desired in the primary
listening area, point the tweeter towards that area; and if less treble is required,
point the tweeter away. Push gently at the edge of the tweeter to point it in the
desired direction. (See Diagram 3) CAUTION: Avoid touching tweeter dome as
damage WILL occur on metal dome tweeters (CSS6 ONE & THREE).
Tweeter Adjustment (CSS6 THREE):
The switch labeled TREBLE allows for 6dB of tweeter adjustment. Your speakers were shipped with
the treble switch in the neutral position, providing the most linear frequency response. If you desire
more treble, roll the switch to the “+” position, and the tweeter will play 3dB higher. If you want less
treble, roll the switch to the “–” position and the tweeter will play 3dB lower. To return to the neutral
setting, slide the switch to the middle position. (See Diagram 4)
Tweeter Adjustment (CSS6 THREE):
The switch labeled TREBLE allows for 6dB of tweeter adjustment. Your speakers were shipped with
the treble switch in the neutral position, providing the most linear frequency response. If you desire
more treble, roll the switch to the “+” position, and the tweeter will play 3dB higher. If you want less
treble, roll the switch to the “–” position and the tweeter will play 3dB lower. To return to the neutral
setting, slide the switch to the middle position. (See Diagram 4)
Woofer Adjustment (CSS6 THREE):
The switch labeled BASS allows for 6dB of bass adjustment. Your speakers were shipped with the bass
set to neutral, resulting in 6Ω of impedance. This setting provides the flattest bass frequency response.
If you desire more bass, roll the switch towards “+” and the bass will play 3dB higher and lower the
impedance to 4Ω. If you want less bass, roll the switch towards “–” and the bass will play 3dB lower
and increase the impedance to 8Ω. This setting provides a more linear bass frequency response. To
return to the neutral setting, slide the switch to the middle position. (See Diagram 5) Remember that
altering the impedance affects the number of speakers able to be driven by an amplifier. If multiple
pairs of speakers are to be driven by one amplifier, SpeakerCraft suggests using the lowest output
position (switch rolled towards the “–” position) until it is determined that the amplifier will operate
properly with the speakers switched to a higher output mode. If you want to safely operate multiple
pairs of speakers, consider purchasing SpeakerCraft S4 or S8 Speaker Selectors.
The switch labeled BASS allows for 6dB of bass adjustment. Your speakers were shipped with the bass
set to neutral, resulting in 6Ω of impedance. This setting provides the flattest bass frequency response.
If you desire more bass, roll the switch towards “+” and the bass will play 3dB higher and lower the
impedance to 4Ω. If you want less bass, roll the switch towards “–” and the bass will play 3dB lower
and increase the impedance to 8Ω. This setting provides a more linear bass frequency response. To
return to the neutral setting, slide the switch to the middle position. (See Diagram 5) Remember that
altering the impedance affects the number of speakers able to be driven by an amplifier. If multiple
pairs of speakers are to be driven by one amplifier, SpeakerCraft suggests using the lowest output
position (switch rolled towards the “–” position) until it is determined that the amplifier will operate
properly with the speakers switched to a higher output mode. If you want to safely operate multiple
pairs of speakers, consider purchasing SpeakerCraft S4 or S8 Speaker Selectors.
SPEAKER INSTALLATION
The unique integral four foot mounting system incorporated into each CSS6 Series speaker allows
for a quick installation by following these easy steps:
for a quick installation by following these easy steps:
1. Remove the grille. It may be necessary to push one or two of the mounting screws and its
attached foot towards the baffle and against the inside surface of the grille to force the grille out
of its retaining groove.
of its retaining groove.
2. Attach the speaker cable (observing the proper polarity with your amplifier, + to + and – to –).
Make sure the left channel of the amplifier is connected to the left speaker, and the right channel is
connected to the right speaker.
connected to the right speaker.
3. Make sure the mounting feet are turned inward to clear the opening, and insert the speaker into the
ceiling. Position the speaker into the hole.
Note: The flange of the speaker is designed to flex and
conform to any small imperfections in the ceiling’s surface. Tighten the four screws on the front of the
baffle only enough to make the flange become snug against the ceiling. As you tighten the screws,
the feet will automatically flip into an outward position (See Diagram 4), thereby clamping the dry-
wall between the feet and the flange. CAUTION: Over tightening may warp the baffle, crack the
ceiling, cause flange to distort, and make the grille difficult to install.
baffle only enough to make the flange become snug against the ceiling. As you tighten the screws,
the feet will automatically flip into an outward position (See Diagram 4), thereby clamping the dry-
wall between the feet and the flange. CAUTION: Over tightening may warp the baffle, crack the
ceiling, cause flange to distort, and make the grille difficult to install.
4. Push the grille firmly into the slot in the speaker baffle.
PAINTING THE SPEAKERS
If you plan to paint your speakers, we recommend that it be done prior to installation. If you plan to
paint your speakers sometime in the future, it is best to remove them by simply reversing the steps for
“SPEAKER INSTALLATION” on page 2. If it is necessary to paint the speakers while they are still in the ceiling, the paint masks provided in
the carton must be installed in place of the grille while the flange is being painted with the ceiling. The grilles can also be painted, how-
ever, great care should be taken not to clog the holes, as this will greatly reduce the sound quality of the speakers. SpeakerCraft recom-
mends only light spray painting using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are attached to the speaker.
If it is necessary to paint the under grille material, follow the same procedure used to paint the grilles.
paint your speakers sometime in the future, it is best to remove them by simply reversing the steps for
“SPEAKER INSTALLATION” on page 2. If it is necessary to paint the speakers while they are still in the ceiling, the paint masks provided in
the carton must be installed in place of the grille while the flange is being painted with the ceiling. The grilles can also be painted, how-
ever, great care should be taken not to clog the holes, as this will greatly reduce the sound quality of the speakers. SpeakerCraft recom-
mends only light spray painting using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are attached to the speaker.
If it is necessary to paint the under grille material, follow the same procedure used to paint the grilles.
SPECIAL FIRE WALL INSTALLATION
If you plan to mount your speakers in a fire-rated ceiling, you should purchase SpeakerCraft CSS6 Sound Enclosures. The metal enclosures
mount easily between joists, and contain a standard electrical type connector for connections of your speaker cable directly to the speaker.
mount easily between joists, and contain a standard electrical type connector for connections of your speaker cable directly to the speaker.
Diagram 2:
Ceiling Cut Out
Diagram 3:
Tweeter
Diagram 4:
Treble Adjustment Switch
Diagram 6:
Mounting Feet
Diagram 5:
Bass Adjustment Switch
Push Tweeter
Here
LIMITED LIFETIME WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship,
provided the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were pur-
chased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable
to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be
borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in materials or
workmanship at any time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace this product
at no additional charge, except as set forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option
may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting
surface may be required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced
parts and product become the property of SpeakerCraft Inc. Products replaced or repaired under this warranty will be returned to the original retail
purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or ship-
ping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has
not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This
Warranty will be void if the Serial Number on the product has been removed, tampered with or defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole
remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or consequential damages arising out
of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such
damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on the length of an implied
warranty. If the original retail purchaser resides in such a state, this limitation does not apply.