KitchenAid 22.7 Cu. Ft. Counter Depth Side-by-Side Refrigerator with Exterior Ice and Water Installation Guide

Gather the required tools and parts before starting installation. 

Read and follow the instructions provided with any tools listed 

here.
TOOLS NEEDED:  

 Your refrigerator dealer has a kit available with a ¹⁄₄" 

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. 

Before purchasing, make sure a saddle-type valve complies with 

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆" 

(4.76 mm) saddle valve which reduces water flow and clogs more 

easily.
IMPORTANT:

■

All installations must meet local plumbing code requirements.

■

Use copper tubing and check for leaks. Install copper tubing 

only in areas where the household temperatures will remain 

above freezing.

A cold water supply with water pressure of between 30 and 

120 psi (207 and 827 kPa) is required to operate the water 

dispenser and ice maker. If you have questions about your water 

pressure, call a licensed, qualified plumber.

■

If your refrigerator has a water dispenser: After installation is 

complete, use the water dispenser to check the water 

pressure.

■

With the water filter removed, dispense 1 cup (237 mL) of 

water. If 1 cup of water is dispensed in 8 seconds or less, 

the water pressure to the refrigerator meets the minimum 

requirement.

■

If it takes longer than 8 seconds to dispense 1 cup of 

water, the water pressure to the refrigerator is lower than 

recommended. See “Problem Solver” for suggestions.

 The pressure of the water supply coming out of a 

reverse osmosis system going to the water inlet valve of the 

refrigerator needs to be between 30 and 120 psi (207 and 

827 kPa).
If a reverse osmosis water filtration system is connected to your 

cold water supply, the water pressure to the reverse osmosis 

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 

40 to 60 psi (276 to 414 kPa):

■

Check to see whether the sediment filter in the reverse 

osmosis system is blocked. Replace the filter if necessary.

■

Allow the storage tank on the reverse osmosis system to refill 

after heavy usage.

■

If your refrigerator has a water filter, it may further reduce the 

water pressure when used in conjunction with a reverse 

osmosis system. Remove the water filter. See “Water Filtration 

System” in the User Instructions, User Guide, or Use & Care 

Guide.

If you have questions about your water pressure, call a licensed, 

qualified plumber.

Dispose of/recycle all packaging materials. Do not use sharp 

instruments, rubbing alcohol, flammable fluids, or abrasive 

cleaners to remove tape or glue. These products can damage the 

surface of your refrigerator.
IMPORTANT: 

■

Use ¹⁄₂" socket wrench to remove skids (socket extension is 

recommended).

■

All four leveling legs must contact the floor to support and 

stabilize the full weight of the refrigerator.

After you remove all of the package materials, clean the inside of 

your refrigerator before using it. See the cleaning instructions. 

■

Flat-blade screwdriver

■

⁷⁄₁₆" and ¹⁄₂" open-end or 

two adjustable wrenches

■

¹⁄₄" nut driver

■

¹⁄₄" drill bit

■

Cordless drill

Your refrigerator is heavy. When moving the refrigerator for 
cleaning or service, be sure to cover the floor with 
cardboard or hardboard to avoid floor damage. Always pull 
the refrigerator straight out when moving it. Do not wiggle or 
“walk” the refrigerator when trying to move it, as floor 
damage could occur.

Do not clean glass shelves or covers with warm water when 
they are cold. Shelves and covers may break if exposed to 
sudden temperature changes or impact, such as bumping. 
Tempered glass is designed to shatter into many small, 
pebble-size pieces. This is normal. Glass shelves and covers 
are heavy. Use both hands when removing them to avoid 
dropping.