KitchenAid 30-Inch 4 Burner Gas Rangetop, Commercial-Style Installation Guide

Check that all parts are included.

 

■

Gas pressure regulator

 

■

Burner grates

 

■

Burner bases and burner caps

 

■

Grill grate (on grill models)

 

■

Wave tray (on grill models)

 

■

Flame spreader (on grill models)

 

■

Burner assembly (on grill models)

 

■

Grease trays (2) (on grill models)

 

■

Griddle drip tray (on griddle models)

 

■

Grill drip tray (on grill models)

 

■

Foam tape

 

■

LP orifice package (W10393255)

 

■

Conversion label (W10393342)

NOTE: The cooktop is manufactured for use with Natural gas. 

To convert to LP gas, see the “Gas Conversions” section.

48" (121.9 cm) models and grill models must be installed with 

a backsplash if installing at zero clearance to a combustible 

backwall. See “Cabinet Dimensions” in the “Location 

Requirements” section for installation requirements.

 

■

36" (91.4 cm) Retractable Backguard 

Order Part Number 8284756

 

■

48" (121.9 cm) Retractable Backguard 

Order Part Number 8284755

 

■

9" (22.9 cm) Backguard for 36" (91.4 cm) Cooktops 

Order Part Number W10115776

 

■

9" (22.9 cm) Backguard for 48" (121.9 cm) Cooktops 

Order Part Number W10115777

 

■

22" (55.9 cm) Backguard with Shelf for 36" (91.4 cm) 

Cooktops 

Order Part Number W10225949

 

■

22" (55.9 cm) Backguard with Shelf for 48" (121.9 cm) 

Cooktops 

Order Part Number W10225948

To order, see the “Assistance or Service” section of the Use and 

Care Guide.
Check local codes and consult gas supplier. Check existing gas 

supply and electrical supply. See the “Electrical Requirements” 

and “Gas Supply Requirements” sections.

To convert the cooktop for elevations above 6,560 ft (1999.5 m), 

order a High Altitude Conversion Kit.

 

■

Part Number W10394296 - LP high altitude

 

■

Part Number W10394295 - Natural gas high altitude

To order, see the “Assistance or Service” section of the Use and 

Care Guide.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. 

Do not obstruct flow of combustion and ventilation air.

 

■

It is the installer’s responsibility to comply with installation 

clearances specified on the model/serial/rating plate. The 

model/serial/rating plate is located on the underside of the 

cooktop burner base.

 

■

It is recommended that a 600 CFM or larger vent hood 

be installed above the cooktop.

 

■

It is not recommended that a microwave hood combination 

be mounted above the cooktop.

 

■

The cooktop should be installed in a location away from 

strong draft areas, such as windows, doors, and strong 

heating vents or fans.

 

■

All openings in the wall or floor where cooktop is to be 

installed must be sealed.

 

■

Cabinet opening dimensions that are shown must be used. 

Given dimensions are minimum clearances.

 

■

Grounded electrical supply is required. See the “Electrical 

Requirements” section.

 

■

Proper gas supply connection must be available. See the 

“Gas Supply Requirements” section.

 

■

The cooktop is designed to hang from the countertop 

by its side or rear flanges.

 

■

The gas and electric supply should be located as shown in 

the “Gas and Electric Connection Locations” section so that 

they are accessible without requiring removal of the cooktop.

 

■

Provide cutout in left rear corner of cutout enclosure as 

shown to provide clearance for gas inlet, power supply cord, 

and to allow the rating label to be visible.

IMPORTANT: To avoid damage to your cabinets, check with 

your builder or cabinet supplier to make sure that the materials 

used will not discolor, delaminate, or sustain other damage.

The installation of this cooktop must conform to the 

Manufactured Home Construction and Safety Standard, 

Title 24 CFR, Part 3280 (formerly the Federal Standard for 

Mobile Home Construction and Safety, Title 24, HUD Part 

280). When such standard is not applicable, use the Standard 

for Manufactured Home Installations, ANSI A225.1/NFPA 501A, 

or local codes. 
In Canada, the installation of this cooktop must conform with 

the current standards CAN/CSA-A240 latest edition, or with 

local codes.