AL-KO SnowLine 560 II 112 933 User Manual
GB
25
469186_c
Snow Line 560 II, 620 II, 620E II
Use the skid plates to adjust the distance of the
FOHDULQJSODWHIURPWKHVXUIDFH'RQRWRSHUDWH
WKHPDFKLQHRQJUDYHOVXUIDFHV
1HYHUOLIWRUFDUU\WKHPDFKLQHZKLOHWKHHQJLQHLV
running.
'RQRWHDWGULQNRUVPRNHZKLOH¿OOLQJZLWKSHWURO
or engine oil.
'RQRWLQKDOHSHWUROIXPHV
Take precautions to ensure that discharged snow
GRHVQRWFDXVHLQMXU\WRSHUVRQVRUDQLPDOVRU
GDPDJHWREXLOGLQJVYHKLFOHVRURWKHUREMHFWV
0DNHVXUHWKDWWUDI¿FLVQRWLPSDLUHGDQGWKDWGULY-
ers are not endangered.
ers are not endangered.
Keep hands out of the snow discharge chute while
WKHPDFKLQHLVUXQQLQJ
.HHSKDQGVDQGIHHWDZD\IURPWKHDXJHUDQGLP-
SHOOHUZKLOHWKHPDFKLQHLVUXQQLQJ
'RQRWFOHDUVQRZIURPURRIV
Assembly
Caution!
'RQRWRSHUDWHWKHPDFKLQHXQWLOLWKDVEHHQIXOO\
'RQRWRSHUDWHWKHPDFKLQHXQWLOLWKDVEHHQIXOO\
DVVHPEOHG
Required tools
2 Open-end or ring spanners, size 10
Open-end or ring spanner, size 13
+H[NH\PP
&RPELQDWLRQRUQHHGOHQRVHSOLHUV
Screwdriver
Spray oil
7\UHSXPSZLWKSUHVVXUHJDXJHDXWRW\UHYDOYH
Assembly sequence
Attaching and adjusting control cables
7KHVDPHSURFHGXUHDSSOLHVIRUWKHZKHHOGULYH
and auger control cables.
and auger control cables.
1. Guide the control cable upward:
Guide the auger control cable through the
opening on the drive speed selection plate
(
(
3-1).
Guide the wheel drive control cable upward
under the drive speed selection plate (
under the drive speed selection plate (
3-2).
2.
/RRVHQWKHVFUHZZLWKWKHKRRNIURPWKHDGMXVW-
PHQWQXW( 4-1)7KHORFNQXWUHPDLQVRQWKH
screw.
screw.
3. Raise the clutch lever (
5).
4. Mount the hook into the hole on the clutch lever
IURPWKHJXLGHKDQGOHVLGH( 6).
5.
6FUHZWKHDGMXVWPHQWQXWWRWKHDWWDFKHGVFUHZ
until there is no slack in the cable (lightly tightened)
(
until there is no slack in the cable (lightly tightened)
(
7-1). Hold the cable while tightening so that it
does not twist.
6. Tighten the lock nut (
7-2).
» The control cables are installed.
Attaching the drive speed selection lever
1.
*XLGHWKHSUHDVVHPEOHGGULYHVSHHGVHOHFWLRQ
lever through the drive speed selection plate
(
lever through the drive speed selection plate
(
8-1).
2.
5HPRYHWKHPRXQWLQJVFUHZIURPWKHFRQQHFWLRQ
bolt and attach the drive speed selection lever
(
bolt and attach the drive speed selection lever
(
9).
3. Secure the drive speed selection lever with the
KRUL]RQWDOPRXQWLQJVFUHZ( 10-1). Do not tighten
the screw yet.
the screw yet.
4.
$GMXVWWKHOHYHUSRVLWLRQZLWKWKHDGMXVWPHQWVFUHZ
VRWKDWLWHQJDJHVLQWRWKHVORWIRUWKH¿UVWVSHHG
setting (1) (
setting (1) (
8-2).
5.
/RFNWKHDGMXVWPHQWVFUHZ( 10-2).
6.
7LJKWHQWKHPRXQWLQJVFUHZZLWKWKHVHOIORFNLQJ
nut (
nut (
10-1).
» The drive speed selection lever is attached.
Attaching the snow discharge chute
1. Lightly lubricate the surface of the snow discharge
chute that slides against the snow blower with
spray oil (
spray oil (
11).
2. Mount the discharge chute (
11).
3.
,QVHUWPRXQWLQJVFUHZVLQWRWKHORZHUODUJHUJXLGH
SODWHDQGDWWDFKWKHVPDOOHUJXLGHSODWH( 12-1).