Samsung HT-X810 User Manual
16
connections
17
ENG
●
CONNECTIONS
INSTALLING THE WALL MOUNT
Place the Mounting Studs on the rear of the product and
turn them clockwise to fi x.
turn them clockwise to fi x.
Place the wall mount bracket on a wall surface so that
the arrow on it points upward, and then secure it
with four screws (not supplied).
the arrow on it points upward, and then secure it
with four screws (not supplied).
Then, fi t the product (Mounting Studs installed) into the
corresponding hole of the wall mount bracket.
For secure installation, make sure the mounting studs
go down to the bottom of the hole.
corresponding hole of the wall mount bracket.
For secure installation, make sure the mounting studs
go down to the bottom of the hole.
This is the completion of the wall mount installation.
1.
2.
3.
4.
Secure the Home Cinema fi rmly to the wall so that it does not fall off.
If the Home theater falls off, it may result in an injury or damage to the product.
If the Home theater falls off, it may result in an injury or damage to the product.
When the Home Cinema is installed on wall, please make sure that a child does not pull any of
connecting cables. as it may cause it to fall.
connecting cables. as it may cause it to fall.
Mounting Studs (2EA)
(supplied)
CONNECTING THE WIRELESS SUBWOOFER
Press the POWER button on the rear of the subwoofer to turn it on.
If the main unit is turned on
The subwoofer will be automatically connected to the product and
the Link LED on its front will blink blue for a few seconds.
The subwoofer will be automatically connected to the product and
the Link LED on its front will blink blue for a few seconds.
If the main unit is turned off
The Link LED on the front of the subwoofer will blink blue
for about 30 seconds, then will change to red as the sub
switches to STANDBY mode.
The Link LED on the front of the subwoofer will blink blue
for about 30 seconds, then will change to red as the sub
switches to STANDBY mode.
If the subwoofer is turned off, you will see S/W CHECK on the display panel of the main unit.
Place the wireless subwoofer under the main unit.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other
device that uses the same frequency (5.8GHz) near the system, some sound interruption may be
heard due to interference.
device that uses the same frequency (5.8GHz) near the system, some sound interruption may be
heard due to interference.
The transmission distance of radio wave is about 10M, but may vary depending on your operating
environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless
subwoofer, the system may not operate at all, because the radio wave cannot penetrate metal.
environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless
subwoofer, the system may not operate at all, because the radio wave cannot penetrate metal.
If the main unit doesn't make wireless connection, the system needs ID Setting between the main
unit and wireless subwoofer. With the main unit turned off, press the remote control's
"0"
unit and wireless subwoofer. With the main unit turned off, press the remote control's
"0"
J"1"J"3"J"5" number buttons and the unit will turn on. With the wireless subwoofer turned on,
press ID SET button on the back of the unit for 5 seconds.
•
•
M
This section involves various methods of connecting the Digital Home Cinema to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and
moisture.
For optimal listening performance, make sure that the area around the wireless subwoofer location is clear
of any obstructions.
moisture.
For optimal listening performance, make sure that the area around the wireless subwoofer location is clear
of any obstructions.
ID SET button
POWER button
HT-X810_NO EUR_0401.indd 16-17
HT-X810_NO EUR_0401.indd 16-17
2008-4-9 15:41:05
2008-4-9 15:41:05