Audiovox ce249mp User Manual

Follow the advice below for safe and appropriate operations.

ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty or

humid.

• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor

air flow, by covering it with a cloth, or by placing it on a carpet.

ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not

the cord itself. Pulling the cord may damage it and create a hazard.

• When you are not going to use the unit for a long period of time,

disconnect the AC power cord.

ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your

local voltage.

• When there is condensation inside the unit, the unit may not function

normally.

• Let it stand for 1 to 2 hours before turning the power on, or gradually

heat the room up and dry the unit before use.

FCC INFORMATION (for USA)
This device complies with part 15 of FCC Rules. Operations are subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including

interference that may cause undesirable operations.

RATING PLATE LOCATION
The rating plate location is on the bottom of product.

Printed in China                                                                                                                 811-136191-033

GENERAL
Power consumption: 15 W
Power source:

AC 120V~60 Hz (USA and Canada)
AC 220V ~50Hz (China)
AC 220V ~60Hz (Korea)
AC 230V~50 Hz (Europe and Hong Kong)
AC 240V~50 Hz (Australia)
AC 110-120V/220-240V~50/60Hz (Others)
DC 9V (6 x "C" size or UM-2 batteries)

It's important that you periodically clean the laser lens:
1. Turn off the unit's power and disconnect the AC

power.

2. Open the CD door and remove the disc.

3. Clean the lens with a soft cloth or use an air blower

brush designed for cameras.

4. If you still are not able to remove dirt particles, moisten

a cotton swab with isopropyl alcohol and gently
apply to the face of the laser lens, rubbing gently
until all traces of dirt are removed.

Although the music tracks in the disc are covered with a
protective layer, it is still advisable to treat the disc
carefully. Always pick up discs by the edge and put them
back in their holders immediately after use.

• Should the CD door be opened before the reading of the CD is completed,

a jamming noise may occur. This can be resolved by closing the CD door
and then sliding the FUNCTION switch temporarily to OFF.

• If an abnormal display indication or an operating problem occurs, discon-

nect the AC power cord and remove the batteries. Wait at least 5 seconds,
then reconnect the AC power cord or reinstall the batteries.

Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft
cloth.

Laser lens

To PRESET RADIO STATIONS
You can tune in a stored station directly by pressing DIRECTORY/PRESET
button.
10 stations on FM band can be preset.
10 stations on AM (MW) band can be preset.

1.  Slide the FUNCTION switch to RADIO.
2.  Press the BAND   button to select a band and tune the TUNING 

or 

  button to choose a desired station.

3.  Press the PGM button, “MEMORY” indicator will blink on the display.
4.  Press the DIRECTORY/PRESET –/+ button to select desired number.
5.  Press PGM button again to store the preset station.
6.  Repeat steps 2 to 5 until the desired station are presetted (up to 10

stations).

TUNING IN A PRESETTED STATION
Press the DIRECTORY/PRESET –/+ button to select a presetted number.
After pressing the button, the presetted number (such as “P01”) is displayed
2 seconds, then the frequency is displayed.
The “MEMORY” indicator is displayed during the preset tuning.

FM : To improve FM reception,

extend the antenna.

Note : After listening, slide the FUNCTION switch to OFF.

NOTE:
While the reception is strong stereo broadcast, the “ 

 ”  icon will

appear on the display.

Problems
Poor FM reception

Poor AM(MW) reception

Solutions
• Make sure AC power plug is secure in

the outlet and inlet has power.

• Batteries may be dead. Install new

batteries.

• Make sure the FUNCTION switch is

set to CD position.

• Make sure disc is clean and

undamaged.

• Make sure printed side of disc is facing

up.

• Make sure PAUSE mode is not

activated.

• Make sure the unit is on a secure spot.

Vibration or jarring can cause the disc
to skip.

Solutions
• Electrical interference in your home

can cause poor reception. Move the
unit away from them (especially those
with motors and transformers).

• Reposition or turn the unit for better

reception.

Problems
System does not turn on
Disc in place but unit
won't play

Should any problem persistes after you have made the following checks,
consult your nearest service faciility.

-

7-

-

8-

-

9-

-

10-

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING:  TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK) NO USER-SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO  QUALIFIED
SERVICE PERSONNEL.

The lightning flash
and arrowhead
within the triangle is
a warning sign
alerting you of
"dangerous voltage"
inside the product.

The exclamation
point within the
triangle is a warning
sign alerting you of
important instructions
accompanying the
product.

INVISIBLE LASER RADIATION WHEN

OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM

• Do not touch the laser lens on the CD player.

• Temperature changes can cause condensation to form on the laser lens.

If condensation forms on the lens, leave the disc compartment door
open (without disc) for an hour to remove condensation.

• Exposure to direct sunlight or extreme heat (such as inside a car parked

in the sun) can cause damage or malfunction.

• To prevent dust from reaching internal parts, keep the compartment door

closed when not using (except when necessary to remove condensation).

AM : To improve AM (MW)

 reception, rotate the unit.