Sony HT-DDW860 User Manual
masterpage:Left
lename[E:\SEM_Janet\Data_HT-
DDW860\Revision_data\J9040000_4255298113DDW860CEL\4255298113\GB09ADD_HT-
DDW860-CEL.fm]
DDW860-CEL.fm]
50
GB
model name1[HT-DDW860]
[4-255-298-11(3)]
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
receiver by the message. Refer to the following
table to solve the problem.
message. You can check the condition of the
receiver by the message. Refer to the following
table to solve the problem.
DEC. EROR
Appears when the signal which the receiver cannot
decode (ex. DTS-CD) is input when “DEC. XXXX”
is set to “DEC. PCM”. Set to “DEC. AUTO”.
decode (ex. DTS-CD) is input when “DEC. XXXX”
is set to “DEC. PCM”. Set to “DEC. AUTO”.
PROTECT
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
If you are unable to remedy the
problem using the
troubleshooting guide
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy the
problem (page 16). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
problem (page 16). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
the receiver’s memory
Amplifier section
Power Output
1)
Models of area code CEL, CEK
(8 ohms 1 kHz, THD 0.7%)
FRONT
(8 ohms 1 kHz, THD 0.7%)
FRONT
2)
: 100
W/ch
CENTER
2)
: 100
W
SURR
2)
: 100
W/ch
SURR BACK
2)
: 100
W
(8 ohms 1 kHz, THD 10%)
FRONT
FRONT
2)
: 120
W/ch
CENTER
2)
: 120
W
SURR
2)
: 120
W/ch
SURR BACK
2)
: 120
W
Models of area code AU
(8 ohms 120 Hz – 20 kHz, THD 0.09%)
FRONT
(8 ohms 120 Hz – 20 kHz, THD 0.09%)
FRONT
2)
: 80
W/ch
CENTER
2)
: 80
W
SURR
2)
: 80
W/ch
SURR BACK
2)
: 80
W
(8 ohms 1 kHz, THD 0.7%)
FRONT
FRONT
2)
: 100
W/ch
CENTER
2)
: 100
W
SURR
2)
: 100
W/ch
SURR BACK
2)
: 100
W
(8 ohms 1 kHz, THD 10%)
FRONT
FRONT
2)
: 120
W/ch
CENTER
2)
: 120
W
SURR
2)
: 120
W/ch
SURR BACK
2)
: 120
W
1) Measured under the following conditions:
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
To clear
See
All memorized settings
Customized sound fields
Specifications
Area code
Power requirements
CEL, CEK
230 V AC, 50 Hz
AU
240 V AC, 50 Hz
MULTI CH IN,
SA-CD/CD, MD/TAPE,
DVD, VIDEO 1, 2
SA-CD/CD, MD/TAPE,
DVD, VIDEO 1, 2
Sensitivity: 800 mV
Impedance: 50 kiloohms
Impedance: 50 kiloohms
GB01COV_HT-DDW860-CEL.book Page 50 Monday, March 29, 2004 10:42 AM