Yamaha A-S700 User Manual

Page of 22
iii 
En
1
To assure the finest performance, please read this manual 
carefully. Keep it in a safe place for future reference.
2
Install this sound system in a well ventilated, cool, dry, clean 
place – away from direct sunlight, heat sources, vibration, 
dust, moisture, and/or cold. Allow ventilation space of at least 
30 cm (11-13/16 in) on the top, 20 cm (7-7/8 in) on the left 
and right, and 20 cm (7-7/8 in) on the back of this unit. 
3
Locate this unit away from other electrical appliances, motors, 
or transformers to avoid humming sounds.
4
Do not expose this unit to sudden temperature changes from 
cold to hot, and do not locate this unit in an environment with 
high humidity (i.e. a room with a humidifier) to prevent 
condensation inside this unit, which may cause an electrical 
shock, fire, damage to this unit, and/or personal injury.
5
Avoid installing this unit where foreign objects may fall onto 
this unit and/or this unit may be exposed to liquid dripping or 
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or 
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire, 
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and 
liquid may cause electrical shock to the user and/or 
damage to this unit. 
6
Do not cover this unit with a newspaper, tablecloth, curtain, 
etc. in order not to obstruct heat radiation. If the temperature 
inside this unit rises, it may cause fire, damage to this unit, 
and/or personal injury.
7
Do not plug in this unit to a wall outlet until all connections 
are complete.
8
Do not operate this unit upside-down. It may overheat, 
possibly causing damage.
9
Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, 
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might 
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this 
unit with a higher voltage than specified is dangerous and may 
cause fire, damage to this unit, and/or personal injury. 
Yamaha will not be held responsible for any damage resulting 
from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable 
disconnected from a wall outlet or the unit during a lightning 
storm.
14 Do not attempt to modify or fix this unit. Contact qualified 
Yamaha service personnel when any service is needed. The 
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time 
(i.e. vacation), disconnect the AC power plug from the wall 
outlet.
16 Install this unit near the AC outlet and where the AC power 
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section in the 
owner’s manual on common operating errors before 
concluding that this unit is faulty.
18 Before moving this unit, press POWER to turn off this unit 
and then disconnect the AC power plug from the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit 
must be set for your local main voltage BEFORE plugging 
into the wall outlet. Voltages are:
Asia model.............................. AC 220/230-240 V, 50/60 Hz
General model ..........AC 110/120/220/230-240 V, 50/60 Hz
20 The batteries shall not be exposed to excessive heat such as 
sunshine, fire or like.
21 Excessive sound pressure from earphones and headphones 
can cause hearing loss.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
As long as this unit is connected to the AC wall outlet, 
it is not disconnected from the AC power source even 
if you turn off this unit by POWER or set it to the 
standby mode by   button on the remote control.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC 
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN 
OR MOISTURE.
This unit enters the standby mode when you press 
POWER inward to the ON position and then press   
button on the remote control. In this state, this unit is 
designed to consume a very small quantity of power.