Silex Technology C-6700WG User Manual

C-6700WG

Power Supply

Setup Guide

Warranty Booklet

CX User Software

Contents

For User Registration

Rubber Feet

Stand

When the product is placed in the horizontal (side) position, please use the rubber feet provided to prevent the unit from sliding.  

Place one on each corner.

Customer Support

USA : silex technology america, Inc.
    E-mail : support@silexamerica.com
    URL : http://www.silexamerica.com/

    Phone: 801-748-1199

    US Toll Free Phone: 866-765-8761

Safety instructions are noted in the Readme file on the CX User Software . Be sure to read 
them before using this product.
- Safety instructions regarding the radio waves

Please note the following instructions:

- Do not use this product near medical devices such as a heart pacemaker. The radio 

wave generated by this product may interfere with the operation of these devices and 
may threaten one's life.

- Do not use this product near microwave ovens. The radio wave used by microwave 

ovens may cause interference to this product.

W A 0 3 7 9 0 X X

To  use  this  product  over  the  wireless  LAN  network,  you  need  to  configure  wireless  LAN 

settings  as  appropriate  for  your  network.  This  information  needs  to  be  identical  to  the 

communication devices such as an access point.

Please collect the following information before the setup.

Wireless mode

SSID

Encryption 
method

Ad hoc  (ch.     )    /    Infrastructure

WEP KEY 
 or 
Pre-Shared 
Key

     

 WEP     

(Open / Shared)

Encryption 
method

/   WPA   /   WPA2

Write down your network configuration

Insert the CD-ROM (CX User Software) into your Windows PC. 

Startup menu is displayed.
Click 

Print Server Setup.

CX Wireless Setup screen is displayed.

Check the notes on the screen and select 

computer and click Next.

Read the SOFTWARE LICENSE AGREEMENT and click 

Yes.

To ensure these settings take effect, 

unplug the AC adapter from the electrical 

outlet and then plug it back in.

-USB cable

The following item is required:

1. Remove the AC plug from the electric outlet.
2. Push and hold the button on the print server while re-inserting the AC plug 

 into the electric outlet. Continue holding.

3. The Status LED(Orange) will light when the factory default configuration 

settings have been restored. Release the push switch.

Install the printer driver on your PC.

For details, refer to the manual that came with 

your printer.

Connect the AC adapter to this product and the power 

plug to the outlet. 

(Do not connect the printer to this product yet. Printer 

will be connected in ‘18’) 

Verify the Wireless LED(Green) blinks.

Click Wireless.

 * In a Windows XP (SP2 or higher) or Vista environment, the above message  

will be displayed. Select Yes

.

*  The User Account Control screen is displayed when configuration is performed 

on Windows Vista. Select Continue. 

Select Get IP Address Automatically

 

and click Next.

Confirm the configuration parameters and 

click 

Execute.

* If the wireless network that you wish to use is not shown in 

the list, click 

Detailed Config and configure each setting.

If the screen above is displayed, you need to change 
the wireless settings on the PC manually.
Read the message and click OK.

Select a product to be configured and click 

Next.

*  If your product is not displayed on the list, click Refresh.

*  If multiple  products  are  displayed  in  the  list,  check  the 

Ethernet Address on the label of this product.

Select Yes and click Finish.

<<  If you did not need to change the 

         wireless settings on the PC manually 

         in ‘11’, this screen will appear           >>

Click 

Finish. 

Change the wireless settings on the PC 

(that you have manually changed) back

to the previous settings written down in

‘11’. 

If the screen above is displayed, select the wireless 

network card to be used and click OK.

*  

This screen is displayed only when two or more 

network cards are installed on your PC.

Select this product and click Next.

Use to connect this product and a printer. 

There is no need to purchase a new USB cable when a cable was 

bundled with the printer to be connected to this product. 

Check the message and click OK.

*  If you use Windows XP or Vista and the setup utility automatically 

changed the wireless settings on the PC, this screen is not displayed.

If the wireless settings on the PC differ from the 

configuration information on the screen above, change 

the PC wireless settings to match those displayed on 

the screen.

Verify the wireless settings on the PC and click Next.

*  Application  install  screen  will  be  displayed  as 

shown in Step 2 - 3.

Connect the printer to be shared over the network along 

with this product via a USB cable and insert the power 

plug of this product into the outlet.

This Setup Guide explains how to configure C-6700WG 

(this product) to be used in a wireless LAN environment.

This product has 3 methods of initial configuration as listed below:

-  Configuration through a wireless LAN
-  Configuration through a wired LAN
-  Configuration using a USB memory

This Setup Guide describes how to configure this product through a 

wireless LAN or wired LAN.

For other configuration methods, please refer to the users manual. 

If this product has been used in another network, reset it to the factory default settings.

For details on the factory default configuration, refer to To reset to the factory default settings

.

Perform the factory default configuration according to the connection between this product 

and the PC.

- To perform the factory default configuration with a wireless LAN connection, refer to 

.

- To perform the factory default configuration with a wired LAN connection, refer to 

(Install the printer driver on your PC and make 

sure you can print with a directly attached USB

connection from your computer before using

this product.)

The initial configuration of 

this product is complete and

you do not need to configure

the print server any more. 

After setup is complete on one

computer, each user that wants

to use the Canon printer:

Go to

Step 2: Install the Applications

on the next page

Note: If you manually changed  

the wireless settings at ‘11’

on your PC, go straight to 

‘3’ in Step 2. 

Important:
The print server only needs to be configured on 
one computer. 

After setup is complete, go to:
‘Step 2: Install the Applications’ for each computer 
that will use the printer.

Please refer to your wireless network adapter documentation for 
instructions on how to temporarily change your computer’s wireless 
settings to match those of the print server. 

Important: When you make this temporary change, your computer will 
no longer be connected to the wireless network or Internet. After you 
have completed the setup for the print server, you will need to change 
your computer’s wireless settings back to their current settings. Please 
make sure you write down the settings for your wireless network before 
you make these changes for the print server configuration.

*

<<   If you changed the wireless settings   

          on the PC manually in ‘11’, this 

          screen will appear                                  >>

Select the SSID for your home or office

wireless network. If your network is security 

enabled, enter the network key or password 

and confirm it.  Click Next.

Note: A more detailed manual including troubleshooting tips can be found on the CD 

(Insert the CD, and click on Manual when the Autorun menu appears) of this product.