Edelbrock turbocharger 15012 User Manual
TURBOCHARGER TURBINE INLET STUD KIT
For Exhaust Manifold To Turbine Inlet
Catalog # 15012
INSTALLATION INSTRUCTIONS
Description: Contains the necessary hardware to mount the turbine inlet to the exhaust manifold. The hardware is constructed of
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.
• INSTALLATION:
1. Hand tighten the 1.45” long studs into the exhaust
1. Hand tighten the 1.45” long studs into the exhaust
manifold, with the shorter threads towards the manifold
(See Fig. 1).
2. When attaching the turbocharger to the exhaust manifold,
and the turbo outlet elbow to the turbocharger, use an 8mm
washer under each nut, and hand tighten the 8mm x 1.25
nuts onto the studs.
washer under each nut, and hand tighten the 8mm x 1.25
nuts onto the studs.
3. Torque the 8mm x 1.25 nuts to 190 inch/lbs. (approximately
16 ft/lbs).
Fig. 1
Towards Turbine
Inlet
Towards Exhaust
Manifold
1.45”
• Kit Contents:
Qty.
Description
❑
4
Stud, 8mm x 1.25 x 1.45” long
❑
4
Nut, 8mm x 1.25
❑
4
Washer, 8mm
Edelbrock Corporation
2700 California St. • Torrance • CA • 90503
Tech Line: 1-800-416-8628
E-Mail: Edelbrock@Edelbrock.com
Catalog #15012
Rev. 5/05 - RS/mc
Rev. 5/05 - RS/mc
©2005 Edelbrock Corporation
Brochure #63-0391
TURBOCHARGER TURBINE INLET STUD KIT
For Exhaust Manifold To Turbine Inlet
Catalog # 15012
INSTALLATION INSTRUCTIONS
Description: Contains the necessary hardware to mount the turbine inlet to the exhaust manifold. The hardware is constructed of
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.
• INSTALLATION:
1. Hand tighten the 1.45” long studs into the exhaust
1. Hand tighten the 1.45” long studs into the exhaust
manifold, with the shorter threads towards the manifold
(See Fig. 1).
2. When attaching the turbocharger to the exhaust manifold,
and the turbo outlet elbow to the turbocharger, use an 8mm
washer under each nut, and hand tighten the 8mm x 1.25
nuts onto the studs.
washer under each nut, and hand tighten the 8mm x 1.25
nuts onto the studs.
3. Torque the 8mm x 1.25 nuts to 190 inch/lbs. (approximately
16 ft/lbs).
Fig. 1
Towards Turbine
Inlet
Towards Exhaust
Manifold
1.45”
• Kit Contents:
Qty.
Description
❑
4
Stud, 8mm x 1.25 x 1.45” long
❑
4
Nut, 8mm x 1.25
❑
4
Washer, 8mm
Edelbrock Corporation
2700 California St. • Torrance • CA • 90503
Tech Line: 1-800-416-8628
E-Mail: Edelbrock@Edelbrock.com
Catalog #15012
Rev. 5/05 - RS/mc
Rev. 5/05 - RS/mc
©2005 Edelbrock Corporation
Brochure #63-0391