Smeg s800tl User Manual

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized 
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in 
the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the 

water out.

1. Load the machine, close the drum doors and 

check that they are properly locked.

2. Add detergents and additives into the dispenser 

to no more then the “MAX” level mark, as 
follows:

•

Programme with pre and main wash

•

Main wash programme without prewash

•

Fabric softeners and conditioners

•

Chlorine bleach

•

Stain remover agents

•

Anti-scale agents (if necessary)

3. Turn the programme selector knob to the 

desired programme. 

4. Turn the temperature selector knob to the 

desired temperature.

5. Turn the spin speed selector knob to the 

desired spin speed. If the spin speed “

” is 

selected, the final spin is cancelled, but not the 
intermediate spins. The programme ends with a 
drain cycle.

• For fast, energy saving wash cycles.

• Ideally suited for small loads consisting of lightly 

soiled laundry.

• Can be used for small loads and lightly soiled 

laundry.

• Reduces the water consumption especially during 

the rinses.

• The amount of water is increased to ensure a 

more intensive rinse. 

• This option is particularly suitable for areas with 

very soft water or washing linen laundry for 
people with skin allergies. 

Programme

Temperature 

Selector

(°C)

Load

(kg)

Water

(l)

Energy 

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton

95

5.0

63*

1.80

2:05

Cotton

60

5.0

55

1.20

2:05

Cotton

40

5.0

55

0.55

2:05

Synthetic

60

2.0

56

0.80

1:30

Synthetic

40

2.0

56

0.40

1:30

Delicate

40

1.5

60

0.55

0:45

Wool

40

1.0

60

0.50

0:40

Silk

30

1.0

60

0.30

0:50

• The laundry remains in the last rinse water 

without progressing to the final spin cycle to 
avoid creasing and prevent colours from fading.

• This option is particularly recommended for the 

“Synthetic”, “Delicate” and “Daily Mixed” 
programmes.

• This function is particularly useful if you want to 

postpone spinning to a later time, or if you want 
to drain only.

Note: the programme selector knob stops 
on

.

• Press the “Rinse Hold” button again: the 

programme will terminate automatically with 
the selected spin cycle.

• If you do not wish to spin the clothes, press the 

“On/Off” button, turn the programme selector 
knob to the “Drain” programme and press the 
“On/Off” button again.

Turn on the tap and press the “On/Off” button. 
The indicator light of the “On/Off” button lights up.
Note: If there is a power interruption or if the 
appliance is disconnected during the cycle, the 
programme will run again from the point where it 
was interrupted.

• The programme selector knob is in the Stop 

position.

1. Press the “On/Off” button to switch off the 

machine.

2. Cancel the options.

3. Turn the tap off.

4. Wait for the lid to unlock (about 1 minute).

5.

Open the lid and the drum doors and unload 
the machine.

1. Switch off the machine by pressing the 

“On/Off” button.

2. Select the new programme.

3.

Start programme by pressing the “On/Off” 
button again.

If, for any reason, you wish to interrupt the 
programme for a certain time and continue it later:

1. Press the “On/Off” button.

2. After the desired pause, press again the 

“On/Off” button.

1. Switch off the machine by pressing the 

“On/Off” button.

2. Set the programme selector to “Drain”.

3. Press the “On/Off” button again to start the 

“Drain” programme.