Emerson Process Management 1051 User Manual
1051 & 1052 H & J
Instruction Manual
Form 5587
November 2006
2
Table 1. Type 1051 and 1052 Actuator Specifications
Operation
Direct Acting: Increasing loading pressure
extends the diaphragm rod out of the spring barrel
extends the diaphragm rod out of the spring barrel
Service:
Type 1051: For on-off or throttling service with
positioner
Type 1052: For on-off or throttling service with or
without a positioner
Type 1051: For on-off or throttling service with
positioner
Type 1052: For on-off or throttling service with or
without a positioner
Actuator Sizes
Type 1051: 40, and 60
Type 1052: 40, 60, and 70
Type 1052: 40, 60, and 70
Maximum Diaphragm Sizing Pressure
(2)(3)
Size 40: 4.5 bar (65 psig)
Size 60: 2.8 bar (40 psig)
Size 70: 3.8 bar (55 psig)
Size 60: 2.8 bar (40 psig)
Size 70: 3.8 bar (55 psig)
Maximum Diaphragm Casing Pressure
(2)(3)
Size 40: 5.2 bar (75 psig)
Size 60: 3.4 bar (50 psig)
Size 70: 4.5 bar (65 psig)
Size 60: 3.4 bar (50 psig)
Size 70: 4.5 bar (65 psig)
Maximum Valve Shaft Rotation
90, 75, or 60 deg with optional stops
Torque Limits (mm)
(4)
Limited by maximum diaphragm sizing pressure
or tables 2 and 3, whichever is less
or tables 2 and 3, whichever is less
Stroking Time
Dependent on actuator size, rotation, spring rate,
initial spring compression, and supply pressure. If
stroking time is critical, consult your Emerson
Process Management
initial spring compression, and supply pressure. If
stroking time is critical, consult your Emerson
Process Management
t sales office
Material Temperature Capabilities
(3)
Nitrile Diaphragm or O-Rings
(1)
: –40 to 82
_C
(–40 to 180
_F)
Silicone Diaphragm: –40 to 149
_C (–40 to
300
_F)
Travel Indication
Graduated disc and pointer combination located
on actuator end of valve shaft
on actuator end of valve shaft
Pressure Connections
1/4 in. NPT female
Mounting Positions
See figure 10
Approximate Weights
See table 7
Additional Specifications
For casing pressure ranges and for material
identification of the parts, see the Parts List
identification of the parts, see the Parts List
1. Nitrile O-rings are used in optional top-mounted handwheel, adjustable down travel stop, and adjustable up travel stop assemblies.
2. Use this value to determine the maximum torque output allowed.
3. The pressure / temperature limits in this manual and any applicable standard or code limitation for valve should not be exceeded.
4. Exceeding any torque requirements could damage the actuator and impair safe operation.
2. Use this value to determine the maximum torque output allowed.
3. The pressure / temperature limits in this manual and any applicable standard or code limitation for valve should not be exceeded.
4. Exceeding any torque requirements could damage the actuator and impair safe operation.
Table 2. Output Shaft Diameters and Torque Limits for Actuators With H Mounting
ACTUATOR SIZE
OUTPUT SHAFT DIAMETER
TORQUE LIMIT FOR
H MOUNTING
ACTUATOR SIZE
mm
Inches
N
Dm
Inch-Pounds
40
22.2
28.6
38.1
28.6
38.1
7/8
1-1/8
1-1/2
1-1/2
240
468
468
1110
2120
4140
9815
4140
9815
60
28.6
38.1
38.1
1-1/8
1-1/2
1-1/2
468
1210
4140
10,680
70
(1)
38.1
1-1/2
1210
10,680
1. Type 1052 actuator only.